8D5292 CABLE AS Caterpillar parts
16G
Rating:
Alternative (cross code) number:
CA8D5292
8D-5292
8D5292
CA8D5292
8D-5292
8D5292
Weight: 1 pounds 0 kg.
Information:
LENGTH
3353
mm
MINIMUM BEND RADIUS
127
mm
TRAVEL
76.2
mm
MOTOR GRADER,
Compatible equipment models: 8D5292:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g02254793
Remove the clamps and hose assembly (2).
Remove the bolts, elbow (1), and the O-ring seals.
Remove the bolts, air inlet elbow (3), and the O-ring seal.
Repeat for all of the air inlet elbows.
Illustration 2 g02254854
Attach Tooling (A) and a suitable lifting device to air inlet cover (4). The weight of air inlet cover (4) is approximately 41 kg (90 lb).
Remove bolts (5), air inlet cover (4), and the seal.
Remove the bolts, elbow (6), elbow (7), elbow (8), and the O-ring seals.
Illustration 3 g02254873
Remove the bolts, elbow (9), and the O-ring seals.
If necessary, remove tube assembly (10).
Attach Tooling (A) and a suitable lifting device onto aftercooler core (11). The weight of aftercooler core (11) is approximately 180 kg (400 lb).
Remove bolts (14), aftercooler core (11), and the seal.
If necessary, remove bolts (13) and tanks (12) from the ends of aftercooler core (11). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 5P-3975 Rubber Lubricant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g02254873
If necessary, install tanks (12) and bolts (13) on the ends of aftercooler core (11). Tighten bolts (13) to a torque of 20 5 N m (15 4 lb ft).
Install the seal on the air inlet manifold.
Attach Tooling (A) and a suitable lifting device onto aftercooler core (11). The weight of aftercooler core (11) is approximately 180 kg (400 lb). Position aftercooler core (11) onto the air inlet manifold. Ensure that the bottom seal is properly seated. Install bolts (14).
If necessary, install tube assembly (10).
Apply Tooling (B) to the O-ring seals. Install the O-ring seals, elbow (9), and the bolts.
Illustration 5 g02254854
Apply Tooling (B) to the O-ring seals. Install the O-ring seals, elbow (8), elbow (7), elbow (6), and the bolts.
Attach Tooling (A) and a suitable lifting device to air inlet cover (4). The weight of air inlet cover (4) is approximately 41 kg (90 lb).
Install the seal on the aftercooler core. Position air inlet cover (4) onto the aftercooler core. Ensure that the seal is seated between air inlet cover (4) and the aftercooler core. Install bolts (5).
Illustration 6 g02254793
Install the O-ring seal, air inlet elbow (3), and the bolts.
Apply Tooling (B) to the O-ring seals. Install the O-ring
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g02254793
Remove the clamps and hose assembly (2).
Remove the bolts, elbow (1), and the O-ring seals.
Remove the bolts, air inlet elbow (3), and the O-ring seal.
Repeat for all of the air inlet elbows.
Illustration 2 g02254854
Attach Tooling (A) and a suitable lifting device to air inlet cover (4). The weight of air inlet cover (4) is approximately 41 kg (90 lb).
Remove bolts (5), air inlet cover (4), and the seal.
Remove the bolts, elbow (6), elbow (7), elbow (8), and the O-ring seals.
Illustration 3 g02254873
Remove the bolts, elbow (9), and the O-ring seals.
If necessary, remove tube assembly (10).
Attach Tooling (A) and a suitable lifting device onto aftercooler core (11). The weight of aftercooler core (11) is approximately 180 kg (400 lb).
Remove bolts (14), aftercooler core (11), and the seal.
If necessary, remove bolts (13) and tanks (12) from the ends of aftercooler core (11). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 5P-3975 Rubber Lubricant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 4 g02254873
If necessary, install tanks (12) and bolts (13) on the ends of aftercooler core (11). Tighten bolts (13) to a torque of 20 5 N m (15 4 lb ft).
Install the seal on the air inlet manifold.
Attach Tooling (A) and a suitable lifting device onto aftercooler core (11). The weight of aftercooler core (11) is approximately 180 kg (400 lb). Position aftercooler core (11) onto the air inlet manifold. Ensure that the bottom seal is properly seated. Install bolts (14).
If necessary, install tube assembly (10).
Apply Tooling (B) to the O-ring seals. Install the O-ring seals, elbow (9), and the bolts.
Illustration 5 g02254854
Apply Tooling (B) to the O-ring seals. Install the O-ring seals, elbow (8), elbow (7), elbow (6), and the bolts.
Attach Tooling (A) and a suitable lifting device to air inlet cover (4). The weight of air inlet cover (4) is approximately 41 kg (90 lb).
Install the seal on the aftercooler core. Position air inlet cover (4) onto the aftercooler core. Ensure that the seal is seated between air inlet cover (4) and the aftercooler core. Install bolts (5).
Illustration 6 g02254793
Install the O-ring seal, air inlet elbow (3), and the bolts.
Apply Tooling (B) to the O-ring seals. Install the O-ring
Caterpillar parts catalog:
Parts cable Caterpillar catalog:
4S8783
CABLE 15.12 in.
16, 16G, 225, 235, 3304, 3306, 3406, 627, 627B, 641B, 657B, 666, 666B, 920, 951B, 977K, 992, D343, D348, D353C, D4D, D5, D6C, D7F, D8H, D9G
16, 16G, 225, 235, 3304, 3306, 3406, 627, 627B, 641B, 657B, 666, 666B, 920, 951B, 977K, 992, D343, D348, D353C, D4D, D5, D6C, D7F, D8H, D9G
8W3535
CABLE AS
120B, 120G, 12G, 130G, 140G, 14G, 160G, 16G, 3208
120B, 120G, 12G, 130G, 140G, 14G, 160G, 16G, 3208
4M3136
CABLE ASSEM.
12G, 140G, 14G, 160G, 16G, 215, 225, 235, 245, 910, 931B, 931C, 933, 935B, 935C, 939, 992, D3B, D3C, D3C II, D3C III, D4C III, D5C III
12G, 140G, 14G, 160G, 16G, 215, 225, 235, 245, 910, 931B, 931C, 933, 935B, 935C, 939, 992, D3B, D3C, D3C II, D3C III, D4C III, D5C III
9D3821
CABLE ASSEM.
16G, 215, 215B, 215C, 235, RM-300
16G, 215, 215B, 215C, 235, RM-300
2D8406
CABLE AS
12E, 16G, AD30
12E, 16G, AD30
8W1512
CABLE AS
120B, 120G, 12G, 130G, 140G, 14G, 160G, 16G
120B, 120G, 12G, 130G, 140G, 14G, 160G, 16G
9D7928
CABLE-CONTROL
120G, 12G, 130G, 140G, 14G, 16G
120G, 12G, 130G, 140G, 14G, 16G
8W3630
CABLE AS
12G, 12H, 12H NA, 140G, 140H, 140H NA, 143H, 14G, 160H, 160H NA, 16G
12G, 12H, 12H NA, 140G, 140H, 140H NA, 143H, 14G, 160H, 160H NA, 16G
8D9650
CABLE
14G, 16G
14G, 16G
9D1014
CABLE
16G
16G
8W3629
CABLE AS
16G
16G
8D5291
CABLE AS
14H, 14H NA, 16G
14H, 14H NA, 16G
8W3629
CABLE AS
16G
16G
9D1014
CABLE
16G
16G
8D9650
CABLE
14G, 16G
14G, 16G
8D5288
CABLE AS
14G
14G
8D5289
CABLE AS
14G
14G
5D3940
CABLE AS
120, 120G, 130G, 140, 14E, 16G
120, 120G, 130G, 140, 14E, 16G
1018204
CABLE AS
120H ES, 120H NA, 12H ES, 12H NA, 135H NA, 140H ES, 140H NA, 143H, 14H NA, 160H ES, 160H NA, 163H NA, 16H NA
120H ES, 120H NA, 12H ES, 12H NA, 135H NA, 140H ES, 140H NA, 143H, 14H NA, 160H ES, 160H NA, 163H NA, 16H NA
1155322
CABLE AS
120H ES, 120H NA, 12H ES, 12H NA, 135H NA, 140H ES, 140H NA, 143H, 160H ES, 160H NA, 163H NA
120H ES, 120H NA, 12H ES, 12H NA, 135H NA, 140H ES, 140H NA, 143H, 160H ES, 160H NA, 163H NA
1106398
CABLE AS
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA
1159457
CABLE AS
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA, 163H NA
8C9586
CABLE AS
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA
8D5291
CABLE AS
14H, 14H NA, 16G
14H, 14H NA, 16G