CAGE-BEARING 1424246 - Caterpillar

1424246 CAGE-BEARING Caterpillar parts 515, 525

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1424246
142-4246
1424246

Weight: 33 pounds 14 kg.

Buy CAGE-BEARING 1424246 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SKIDDER,

Compare Prices:

As an associate, we earn commssions on qualifying purchases through the links below

1424246, Contact Insert Module, Male, 12pos for Control, Push-in, 250 V 10 A, HC-M-12-PT-M

$49.99

12 Jan 2024

US: Neutron USA

1424246, Contact Insert Module, Male, 12pos for Control, Push-in, 250 V 10 A, HC-M-12-PT-M
PHOENIX CONTACT USA

Number on catalog scheme: 18

Caterpillar 1424246 Parts scheme CAGE-BEARING

For full view, you need register

Compatible equipment models: 1424246:

WHEEL SKIDDER 515 525 Caterpillar

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

525 Wheel Skidder 1DN00001-02253 (MACHINE) POWERED BY 3304 Engine

138-7614: GEAR GP-OUTPUT TRANSFER » SEBP23900242

515 Wheel Skidder 4LR00001-UP (MACHINE) POWERED BY 3304 Engine

138-7614: GEAR GP-OUTPUT TRANSFER » SEBP24470240

Information:

Illustration 1 g02727904
Accugrade Data LinkThis diagnostic code is recorded when the Implement ECM cannot receive data off the Accugrade data link from the slope sensor. The Implement ECM should receive information from the Accugrade data link at a specific rate.Possible causes of this diagnostic code are listed:
The slope sensor is not functioning.
The termination resistor on the Accugrade data link is disconnected.
The ECM has failed. This condition is unlikely.Test Step 1. CHECK THE INPUT VOLTAGE OF THE SENSOR.
Turn the key start switch to the ON position. Do NOT start the tractor.
Remove the floorplate.Note: Ensure that the tractor has cooled. Avoid contact with the manifold.
Disconnect the machine harness connector for the slope sensor.
Measure the voltage across contact A (wire L872-BU) and contact E (wire T744-WH).Expected Result:The voltage that is measured is between 18 VDC and 32 VDC.Results:
YES - The voltage that is measured is between 18 VDC and 32 VDC. The sensor is receiving the correct voltage. Proceed to test step 2.
NO - The sensor is NOT receiving input voltage. Verify that the connector for the sensor and the harness are correct. Proceed to test step 2.Test Step 2. CHECK THE TERMINATION RESISTOR.
De-energize the system.
The machine harness connector for the sensor remains disconnected.
Measure the resistance across contact C (wire L854-YL) and contact D (wire L855-GN).Expected Result:The resistance that is measured is 60 10 ohms.Results:
YES - The resistance that is measured is 60 10 ohms. Repeat this test step. If the same results occur, an internal component to the sensor has failed.Repair: Replace the sensor.STOP
NO - The resistance that is measured is NOT 60 10 ohms.Repair: Replace the termination resistor.STOPTest Step 3. CHECK THE BATTERY VOLTAGE.
The engine should not be running.
At the battery, measure the voltage of the battery.Expected Result:The voltage that is measured is less than 18 VDC.Results:
YES - The voltage that is measured is less than 18 VDC. The voltage is NOT correct. Repair: Check the charging system. See Special Instruction, REHS0354.STOP
NO - The voltage that is measured is between 18 and 32.5 VDC. There is an open in the circuit between the battery and the sensor.Repair: Repair the machine harness or replace the machine harness.STOP