2894141 CAM-FREEWHEEL Caterpillar parts
30/30, 525B, 525C, 525D, 535B, 535C, 535D, 545, 545C, 545D, 555D, 611, 615C, 950G II, 950H, 950K, 962G II, 962H, 962K, 966G II, 966H, 966K, 966M, 972G II, 972H, 972K, 972M, CX28, D250E, D250E II, D300...  
 
 
Rating:
 Alternative (cross code) number:
CA2894141
289-4141
2894141
 
CA2894141
289-4141
2894141
 
 
  Weight: 5 pounds 2 kg. 
  ARTICULATED TRUCK, WHEEL TRACTOR,
 This part in 2 request: 
Show.
This information for suppliers only!
2020-05-05
2020-04-07
Compatible equipment models: 2894141:
Information:
Illustration 1 g01635456
Medium pressure valve (side view of the swing motor compartment) (3) Medium pressure valve (4) Adjustment screw (main relief valve) (5) Pressure tap (medium pressure)
Install a pressure gauge with a 60000 kPa (8700 psi) capacity on pressure tap (5) for the medium pressure.
Start the engine.
Place the machine controls at the following settings: engine speed dial 10 and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the machine for engine rpm settings.
Warm the hydraulic oil to 50 °C (122 °F).
Set the pilot pressure to the specifications in Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust" for the machine.
Calibrate the solenoid valves for medium pressure. Refer to Testing and Adjusting, "Medium Pressure: Solenoid Valve (Proportional Reducing) - Calibrate" for the Tool Control System.
Set the auxiliary tool mode for medium pressure. Refer to Testing and Adjusting, "Work Tool - Select" for the Tool Control System.Note: To prevent oil flow to the work tool during this testing and adjusting procedure, close the stop valves in the lines for the work tool.
To adjust the pressure setting of the relief valve for medium pressure, press the device for activation for this procedure. Hold the device for activation in this position.Note: Relief action of the relief valve for more than 10 seconds is not allowed.
Check the pressure at pressure tap (5) for medium pressure.
Return the device for activation to the NEUTRAL position.
Compare the pressure reading to the specification 21000 500 kPa (3046 73 psi). If the pressure reading is within the specification, no further adjustment is necessary. If the pressure reading is not within the specification, then proceed to Step 14.
The adjustment screw for the main relief valve is located on the side of valve (3). Turn adjustment screw (4) until the pressure gauge reading at pressure tap (5) is 21000 500 kPa (3046 73 psi).Note: Turning adjustment screw (4) clockwise increases the pressure. Turning adjustment screw (4) counterclockwise decreases the pressure.Note: Always make final pressure adjustment on pressure rise.
Press the device for activation in the opposite direction. Hold the device for activation in this position.
Check the pressure at pressure tap (5) for medium pressure.
Return the device for activation to the NEUTRAL position.
Compare the pressure reading to the specification 21000 500 kPa (3046 73 psi). If the pressure reading is within the specification, no further adjustment is necessary. If the pressure reading is not within the specification, then proceed to Step 14.
Cat SIS web machinery list:
Parts cam Caterpillar catalog:
 2726629
CAM
 
14M, 561N, 621G, 623G, 627G, 824H, 826H, 836H, 950H, 953C, 962H, 963C, 966H, 973C, 994F, AP-1055D, BG-2455D, BG-260D, D5N, D6N
 
14M, 561N, 621G, 623G, 627G, 824H, 826H, 836H, 950H, 953C, 962H, 963C, 966H, 973C, 994F, AP-1055D, BG-2455D, BG-260D, D5N, D6N
 9G7350
CAM
 
611, 613C, 613C II, 613G, 615, 615C, D25C, D30C, D350C, D35C
 
611, 613C, 613C II, 613G, 615, 615C, D25C, D30C, D350C, D35C
 1124893
CAM ASSEM.
 
525B, 539, 613C II, 938G, D6M, IT38G
 
525B, 539, 613C II, 938G, D6M, IT38G
 8R9831
CAM AS-SPIDER
 
518C, 928F, 928G, 938F, 938G, 938G II, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT28F, IT28G, IT38F, IT38G, IT38G II, IT62G, IT62G II, R1300, R1300G, R1300G II
 
518C, 928F, 928G, 938F, 938G, 938G II, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT28F, IT28G, IT38F, IT38G, IT38G II, IT62G, IT62G II, R1300, R1300G, R1300G II
 1189587
CAM-LATCH
 
345B L, 533, 539, 543, 824G, 824G II, 825G, 825G II, 826G, 826G II, 844H, 910G, 924G, 924H, 938G, 938G II, 938H, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980...
 
345B L, 533, 539, 543, 824G, 824G II, 825G, 825G II, 826G, 826G II, 844H, 910G, 924G, 924H, 938G, 938G II, 938H, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 980...
 2T2669
CAM
 
615C
 
615C
 1149490
CAM-SWITCH
 
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G, R1600, R1600G, R1600H, R1700G, R2900, R2900G
 
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G, R1600, R1600G, R1600H, R1700G, R2900, R2900G
 7G8430
CAM-FREEWHEEL
 
615, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, D250D, D25C, D25D, D300B, IT62G II, IT62H, R1600, R1600G
 
615, 950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, D250D, D25C, D25D, D300B, IT62G II, IT62H, R1600, R1600G
 2334463
CAM
 
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT62G II, IT62H
 
950G II, 950H, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT62G II, IT62H
 1655675
CAM AS
 
533, 535B, 950G, TK370, TK371
 
533, 535B, 950G, TK370, TK371
 1258176
CAM-LATCH
 
1090, 1190, 1190T, 1290T, 5130, 5130B, 5230, 5230B, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G II, 826H, 826K, 834G, 834H, 836G, 836H, 844, 844H, 844K, 854G, 854K, 950K, 962K, 966K, 966M, 966M XE,...
 
1090, 1190, 1190T, 1290T, 5130, 5130B, 5230, 5230B, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G II, 826H, 826K, 834G, 834H, 836G, 836H, 844, 844H, 844K, 854G, 854K, 950K, 962K, 966K, 966M, 966M XE,...
 1460719
CAM
 
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
  
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
 1194348
CAM
 
30/30, D250E, D250E II, D300E, D300E II, DEUCE
 
30/30, D250E, D250E II, D300E, D300E II, DEUCE
 2W1922
CAM
 
3508, 3512, 3516
 
3508, 3512, 3516
 6L3798
CAM
 
G3306, G342C, G353D, G398
 
G3306, G342C, G353D, G398
 3745753
CAM-LATCH
 
3512, 3512B, C15 I6, C18 I6, C32, C9
 
3512, 3512B, C15 I6, C18 I6, C32, C9
 2260321
CAM
 
301.5, 301.6C, 302.5, 302.5C, 303, 303.5, 304, 305, 305.5, 305.5E, 306, 306E, 307C, 826C, 904B, 904H, 938G II, 938H, 950G II, 950H, 950K, 953C, 962G II, 962H, 962K, 963C, 966F II, 966G II, 966H, 966K,...
 
301.5, 301.6C, 302.5, 302.5C, 303, 303.5, 304, 305, 305.5, 305.5E, 306, 306E, 307C, 826C, 904B, 904H, 938G II, 938H, 950G II, 950H, 950K, 953C, 962G II, 962H, 962K, 963C, 966F II, 966G II, 966H, 966K,...
 2078683
CAM AS
 
ATS
  
ATS
 7E5863
CAM-TORQUE
 
214B, 3114, 3116, 953B, IT12B, IT14B
 
214B, 3114, 3116, 953B, IT12B, IT14B
 4P4355
CAM-TORQUE
 
211B, 214B, 3114, 3116, 325, 325 LN, AP-1000, CB-434, E120B
 
211B, 214B, 3114, 3116, 325, 325 LN, AP-1000, CB-434, E120B
 1064769
CAM-TORQUE
 
3116, 322B
 
3116, 322B
 4P1696
CAM-TORQUE
 
3116
 
3116
 7D2117
CAM & FOLLOWER AS
 
3406B, 3406E, 3408, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631C, 631E, 631G, 633E II, 637D, 637E, 637G, 639D, 651E, 657E, 657G, 769C, 769D, 771C, 771D, 772, 772B, 773B, 773D, 775B, 775D...
 
3406B, 3406E, 3408, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631C, 631E, 631G, 633E II, 637D, 637E, 637G, 639D, 651E, 657E, 657G, 769C, 769D, 771C, 771D, 772, 772B, 773B, 773D, 775B, 775D...
 1851558
CAM
 
30/30, DEUCE
 
30/30, DEUCE
 
 
 
 
 
 
 
 
 
 
