AVSPARE.COM
parts catalog

CAM-LATCH 5087736 - Caterpillar



5087736 CAM-LATCH Caterpillar parts CAM
Rating:
76
Alternative (cross code) number:
CA5087736
508-7736
5087736
Caterpillar 5087736 CAM-LATCH
Weight: 0.06 pounds 0 kg.

Buy CAM-LATCH 5087736 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 10
 
  For full view, you need register

Information:


Table 2
365B Ultrahigh Demolition Configuration with a total reach of
33 m (108 ft)    
Overall Length (A)    
15499 mm (50 ft 10 inch)    
Overall Height    
4000 mm (13 ft)    
Overall Height    
4310 mm (14 ft)    
Overall Width (B)    
2400 mm (7 ft 10 inch)    
Approximate Total Weight    
17730 kg (39087 lb)    Shipping the Stick
Remove the work tool from the stick.
Illustration 3 g00775806
Stick linkage (A) Stick (B) Power link (C) Pin
Secure power link (B) to the stick.
Locate the supports on the ground. The front support will accept pin (C) of the stick.
Illustration 4 g01035568
(A) Stick (C) Pin (D) Block (E) Bolt (F) Front support (G) Hole (H) Chain (I) Hole (J) Rear support
Lower the front of stick (A) to front support (F) and the rear of the stick to rear support (J) .
Align hole (I) in the stick with holes (G) of the rear support (J) .
Position pin (C) in the lower half of block (D). Secure the block with bolts (E) .
Place chains (H) in order to secure the stick.
Stop the engine. Operate the joysticks in order to release the hydraulic pressure.
Illustration 5 g00775923
(2) Stick (4) Stick cylinder (5) Boom nose (6) Couplings (7) Connector (8) Wood (9) Strap (10) Bolt (11) Pin
Secure the stick cylinder to the boom nose with strap (9) .
Disconnect the quick couplings on both sides of the fore boom.
Disconnect connector (7) .
Remove the hydraulic hoses that are connected to the quick couplings. Plug the hydraulic hoses.
Disconnect the grease lines.
Install a block of wood (8) between the stick and the stick cylinder.
Remove bolt (10) and pin (11) .
Lower the stick cylinder to the stick.
Secure the stick cylinder to the stick.
Disconnect the quick couplings on the top of the fore boom.
Remove the hydraulic hoses. Plug the hydraulic hoses.
Disconnect the grease lines.
Disconnect the electrical wiring.
Illustration 6 g00775963
(2) Stick (12) Fore boom (13) Bolt and washer (14) Pin (15) Spacer
Remove bolt (13) and pin (14) .
Remove spacer (15) .
Start the engine.
Raise the boom.
Drive the machine backward.
Place the stick and the supports on the trailer. Use the four lifting eyes that are on the stick.
Secure the stick to the trailer. Shipping the Boom Nose and the Fore Boom
Illustration 7 g01035563
(1) Rear support (2) Chain (3) Bar on stand in the lower position (4) Hole (5) Boom nose (6) Front support (7) Chain (8) Fore boom (9) Hole
Align holes (4) in the boom nose with holes in rear support (1) .
Illustration 8 g01035537
(5) Boom nose (11) Bracket (12) Block
Align bracket (11) with block (12) .
Install the top of block (12) over bracket (11) .
Install the bolts that secure the two halves of the block together. Tighten the bolts.
Place chains (2) in order to secure the boom nose.
Place chains (7) in order to secure the fore boom.
Stop the engine. Operate the joysticks to all of the full stroke positions. This will release the hydraulic pressure in the system.
Perform the previous steps in reverse in order to assemble the excavator.
Refer to Operation and Maintenance Manual, "Demolition Boom

Caterpillar parts catalog:

Caterpillar parts catalog
980M Wheel Loader MK200001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader MK600001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader KRS00001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader K1Y00001-UP (MACHINE) POWERED BY C13 Engine
982M Wheel Loader F9A00001-UP (MACHINE) POWERED BY C13 Engine
980M Wheel Loader N8T00001-UP (MACHINE) POWERED BY C13 Engine


Parts cam Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.