AVSPARE.COM
parts catalog

CAMSHAFT 3482254 - Caterpillar


3482254 CAMSHAFT Caterpillar parts 735B, 740B, C15, D8T
Rating:
14
Alternative (cross code) number:
CA3482254
348-2254
3482254
Caterpillar 3482254 CAMSHAFT
Weight: 71 pounds 32 kg.

Buy CAMSHAFT 3482254 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK, TRACK-TYPE TRACTOR,

Related part:
3482254  CAMSHAFT  20R1137  R

Compatible equipment models: 3482254:

ARTICULATED TRUCK  735B   740B  
EJECTOR TRUCK 
INDUSTRIAL ENGINE  C15  
TRACK-TYPE TRACTOR  D8T   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Illustration 1. Typical Jacket Water Heater Group: (1) Element Assembly. (2) Cord Assembly. (3) Cap Assembly.5. Remove the yellow plastic dust cap assembly (3) from the heater.6. Insert the element assembly (1) into the core plug hole with the orientation of the element assembly as shown in Illustration 2 for 3114, 3116, and 3126 Engines and Illustration 3 for 3204 and 3208 Engines. The element assembly should be inserted only deep enough so that the tanged washers do not engage the bore.Rotate the element assembly so it does not touch the inner surface of the block. Mark the block and the heater so the heater may again be inserted in this position.
Refer to Special Instruction "Installation of 7E-6310, 9X-3294, 6N-9125, 7E-5244 and 3T-8724 Jacket Water Heater Groups", SEHS9601, for specific engine installation instructions. For 3100 Family of Engines with rear-facing turbocharger turbine, 4P-1603 Turbocharger Shield Group must be installed.7. Remove the heater. Apply a light coat of ethylene glycol to the heater O-ring and the block bore.8. Place the heater into the block bore while indexing the element assembly with the mark from Step 6.9. Place a 11/4 inch deep socket over the threaded end. Insert the heater by evenly and lightly tapping the socket until the heater adapter flange bottoms against the block. Attempting to wedge the heater into the bore will usually result in skewing of the heater and cutting of the O-ring. This procedure, however, may be attempted if space requirements demand this method. If this method is used, DO NOT preload one side.
Illustration 2. Typical Jacket Water Heater Element Assembly For Insertion Into Machines Powered By 3100 Family Of Machine Engines: (A) Orientation of 36 degrees for 3116 and 3126 Engines. (B) Orientation of 45 degrees for 3114 Engine. (4) Right-side Core Plug.10. Install the cap assembly (3) onto the heater.11. Fill the engine with coolant. Start the engine and check for leaks. Continue to operate the engine until the operating temperature is reached in order to assure that all air is purged from the cooling system.12. When the operating temperature is reached, stop the engine. Allow the engine to cool.
Illustration 3. Typical Jacket Water Heater Element Assembly For Insertion Into Machines Powered By 3200 Family Of Machine Engines: 3204 Location-Right rear core plug orientation at twelve o'clock (12:00). 3208 Location-Left rear and right middle core plugs orientation at twelve o'clock (12:00). (5) Retaining Rings (two). (6) O-ring Seal. (7) Chamfer.13. Check the coolant level in the radiator or expansion tank. Top off the coolant as necessary.14. Install the cord assembly (2). Energize the heater. Always unplug the heater before starting the engine.

Caterpillar parts catalog:

Caterpillar parts catalog
C15 Industrial Engine LDN00001-UP
740B Articulated Truck T4R00001-UP (MACHINE) POWERED BY C15 Engine
740B Ejector Articulated Truck T4S00001-UP (MACHINE) POWERED BY C15 Engine
735B Articulated Truck T4P00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR MLN00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR FCT00001-UP (MACHINE) POWERED BY C15 Engine


Parts camshaft Caterpillar catalog:

3310964 CAMSHAFT GP
374F L, 390F L, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 988K, C15, C18, CX31-C18I, D9T
3517366 CAMSHAFT GP
735B, 740B, C15, D8T
3327315 CAMSHAFT
735B, 740B, C18
3482587 CAMSHAFT
374F L, 390F L, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 988K, C15, C18, CX31-C18I, D9T
3731570 CAMSHAFT
12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 160M 2, 160M 3, 160M 3 AWD, 2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 568 FM LL, 586C, 627H, 627K LRC, 725C, 966K, 966M, 966...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.