1606304 CAP-BEARING Caterpillar parts
938G, D6R II, D7H, D7R, D7R II, D7R XR
Rating:
Alternative (cross code) number:
CA1606304
160-6304
1606304
CA1606304
160-6304
1606304
Weight: 14 pounds 6 kg.
TRACK-TYPE TRACTOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$144.13
02 Sep 2022
15.0[6.75] Pounds
US: TakePart
1606304 Cap Bearing Fits Caterpillar 5J1394 7A 7S 7SU 7U 6 D6R II D7R D7R II 57H
TCP Warranty
TCP Warranty
$145.63
08 Jul 2022
15.0[6.75] Pounds
US: ProperBuy
1606304 Cap Bearing Fits Caterpillar 5J1394 7A 7S 7SU 7U 6 D6R II D7R D7R II 57H
TCP Warranty
TCP Warranty
Compatible equipment models: 1606304:
Information:
MID 039 CID 1610 FMI 03Conditions Which Generate This Code:
Illustration 1 g01366153
Connections of the parking brake solenoid 2
This diagnostic code is associated with the parking brake solenoid 2. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1610 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.System Response:The ECM will have no control over the circuit for the solenoid valve. The parking brake will not engage.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J2-43 to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between contact J2-44 and the circuit that has a low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the J2 connector for the ECM, use a wire removal tool to remove wire F923-YL(Yellow) from contact J2-44.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code. Expected Result:The FMI 03 changes to an FMI 05 after the wire is disconnected.Results:
YES - The FMI 03 changes to a FMI 05 after the wire is disconnected. The ECM has responded correctly to the condition of an open circuit. Reinstall the disconnected wire to the correct space in the ECM connector before proceeding to the next Test Step. Proceed to Test Step 3.
NO - The FMI 03 remains active. The status of the active diagnostic code did not change when the wire was disconnected from the ECM.Repair: The ECM has not responded correctly to the condition of an open circuit. The operation of the ECM is not correct. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing,
Illustration 1 g01366153
Connections of the parking brake solenoid 2
This diagnostic code is associated with the parking brake solenoid 2. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1610 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.System Response:The ECM will have no control over the circuit for the solenoid valve. The parking brake will not engage.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J2-43 to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between contact J2-44 and the circuit that has a low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the J2 connector for the ECM, use a wire removal tool to remove wire F923-YL(Yellow) from contact J2-44.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code. Expected Result:The FMI 03 changes to an FMI 05 after the wire is disconnected.Results:
YES - The FMI 03 changes to a FMI 05 after the wire is disconnected. The ECM has responded correctly to the condition of an open circuit. Reinstall the disconnected wire to the correct space in the ECM connector before proceeding to the next Test Step. Proceed to Test Step 3.
NO - The FMI 03 remains active. The status of the active diagnostic code did not change when the wire was disconnected from the ECM.Repair: The ECM has not responded correctly to the condition of an open circuit. The operation of the ECM is not correct. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing,
Caterpillar parts catalog:
Parts cap Caterpillar catalog:
1523421
CAP AS-TRACK IDLER
527, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
527, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
3179080
CAP-TRACK ROLLER
963C, 963D, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
963C, 963D, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
6F3183
CAP-BEARING
3S, 4A, 4S, 518, 5S, 633, 6A, 815B, 955C, 955H, 977D, D3B, D4E, D4E SR, D4H, D4H XL, D5B, D5E, D5H, D5H XL, D5HTSK II, D6H, D6M, D7H, D7R
3S, 4A, 4S, 518, 5S, 633, 6A, 815B, 955C, 955H, 977D, D3B, D4E, D4E SR, D4H, D4H XL, D5B, D5E, D5H, D5H XL, D5HTSK II, D6H, D6M, D7H, D7R
1311647
CAP AS-TRACK IDLER
572R, 572R II, D7H, D7R, D7R II, D7R XR
572R, 572R II, D7H, D7R, D7R II, D7R XR
2733996
CAP-TRACK ROLLER
572R II, D7R, D7R II, D7R XR
572R II, D7R, D7R II, D7R XR
2368191
CAP-MOUNT
D6R, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R XR, D8N
D6R, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R XR, D8N
1933063
CAP-BEARING
834G, 834H, 834K, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T
834G, 834H, 834K, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T
6F7523
CAP
7A, 7S, 8 SR, 824B, 824G, 824G II, 824H, 824K, 824S, 825C, 825G, 825G II, 825H, 825K, 826C, 834, 834B, 836, 8A, 8S, 8U, 9A, D7G, D7G2, D7H, D7R, D7R II, D8H, D8K, D8N, D8R, D9E, D9G, D9L
7A, 7S, 8 SR, 824B, 824G, 824G II, 824H, 824K, 824S, 825C, 825G, 825G II, 825H, 825K, 826C, 834, 834B, 836, 8A, 8S, 8U, 9A, D7G, D7G2, D7H, D7R, D7R II, D8H, D8K, D8N, D8R, D9E, D9G, D9L
3G0910
CAP
24H, 24M, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 844, 844H, 844K, 8A, 8S, D7E, D7E LGP, D7H, D7R, D7R II, D7R XR, D8L, D8N...
24H, 24M, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 844, 844H, 844K, 8A, 8S, D7E, D7E LGP, D7H, D7R, D7R II, D7R XR, D8L, D8N...
1U1212
CAP
D7H, D7R, D7R II, D7R XR
D7H, D7R, D7R II, D7R XR
5J1394
CAP
621, 824B, 834, D7H
621, 824B, 834, D7H
1236305
CAP AS-FUEL TANK
325B L, 350, 854G, 938G, 950G, 972G, 992G, AP-1000B, AP-800C, AP-900B, BG-225B, BG-2455C, BG-245C, IT38G
325B L, 350, 854G, 938G, 950G, 972G, 992G, AP-1000B, AP-800C, AP-900B, BG-225B, BG-2455C, BG-245C, IT38G
3941176
CAP AS
D6R II, D6R III, D6T
D6R II, D6R III, D6T
3179080
CAP-TRACK ROLLER
963C, 963D, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
963C, 963D, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
1523421
CAP AS-TRACK IDLER
527, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
527, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
2683371
CAP AS-CONNECTOR
120M, 12M, 140M, 14M, 160M, 16M, 24M, D10T, D11T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7R II, D7R XR, D8T, D9T
120M, 12M, 140M, 14M, 160M, 16M, 24M, D10T, D11T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7R II, D7R XR, D8T, D9T
2393354
CAP AS
572R II, D6R, D6R II, D6R III, D6T, D7R II
572R II, D6R, D6R II, D6R III, D6T, D7R II
1645798
CAP AS-RAIN
824K, 825K, 826G II, 826H, 834G, 834H, 836G, 836H, 938G, 938H, 950G, 962G, 988G, 988H, D10N, D10R, D10T, D10T2, D6G2 LGP, D6G2 XL, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D7R II, D8N, D8R, D8R...
824K, 825K, 826G II, 826H, 834G, 834H, 836G, 836H, 938G, 938H, 950G, 962G, 988G, 988H, D10N, D10R, D10T, D10T2, D6G2 LGP, D6G2 XL, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D7R II, D8N, D8R, D8R...
1432397
CAP
953C, 953D, 963C, 963D, 973C, 973D, D6K, D6K LGP
953C, 953D, 963C, 963D, 973C, 973D, D6K, D6K LGP
2239110
CAP-TRACK ROLLER
953C, 953D, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
953C, 953D, D5R LGP, D6M, D6N, D6N LGP, D6N OEM
8G0935
CAP
943, 953, 953B, 953C, 953D
943, 953, 953B, 953C, 953D
1559321
CAP AS
561N, 953D, 963D, 973D, D5N, D5R LGP, D6K, D6K LGP, D6N, D6N LGP, D6N OEM, PL61
561N, 953D, 963D, 973D, D5N, D5R LGP, D6K, D6K LGP, D6N, D6N LGP, D6N OEM, PL61
2645425
CAP AS-PROTECTION
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F, 953D, 963D, 973D, D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, ...
793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797F, 953D, 963D, 973D, D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL, D5R LGP, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6N, D6N LGP, ...
2350320
CAP AS-AIR CLEANER
120M, 12M, 140M, 14M, 160M, 16M, 24M, 320D, 330D, 770G, 770G OEM, 772G, 772G OEM, 824H, 826H, 834H, 836H, 953D, 963D, 988H, D10R, D10T, D11R, D11T, D6N, D6N LGP, D6R II, D6R III, D6T, D6T XL, D7E, D7E...
120M, 12M, 140M, 14M, 160M, 16M, 24M, 320D, 330D, 770G, 770G OEM, 772G, 772G OEM, 824H, 826H, 834H, 836H, 953D, 963D, 988H, D10R, D10T, D11R, D11T, D6N, D6N LGP, D6R II, D6R III, D6T, D6T XL, D7E, D7E...