2892360 CAP Caterpillar parts
C6.6, C7.1
Rating:
Alternative (cross code) number:
CA2892360
289-2360
2892360
CA2892360
289-2360
2892360
Weight: 1 pounds 0 kg.
GENERATOR SET, INDUSTRIAL ENGINE,
Number on catalog scheme:
22B
For full view, you need register
Information:
Shimming Procedure
Illustration 1 g00598596
(1) 134-3250 Bearing (2) 6V-3249 Bearing (3) 134-3253 Thrust Bearing (4) 8C-8843 Bolt (5) 6K-3632 Locknut (6) 134-3254 Shim Kit (7) 134-3255 Shim (8) 8T-4223 Hard Washer (9) 3B-8489 Grease Fitting (10) 136-6169134-4078 Pinion Gear (11) 134-3243 Saddle Cap Assembly (12) 3Y-6887 Dowel (13) 6V-8190 Nut Note: Use 7M-7456 Bearing Mount Compound on all fasteners.
Insert 134-3250 Bearing (1) into 134-3243 Saddle Cap Assembly (11) .
Use the following procedure to determine the amount of shims that are needed:
Put 134-3253 Thrust Bearing (3) into the base of the casting. Put the King Post on top of the thrust bearing. Install 134-3255 Shim (7) onto the top of the shaft of 136-6169 Kingpost Assembly (10). Seat the shaft against the radius of the King Post. Make sure that the shaft is seated tightly. Do not install 6V-32493G-5337 Bearing (2) at this time.
Slip 134-3243 Saddle Cap Assembly (11) over the top shaft of the King Post. Slide the saddle cap assembly downward until the cap makes full contact with the Kingpost assembly.
Illustration 2 g00740636
(A) 355.6 mm (14.0 inch) (B) 800 mm (31.5 inch) (C) 701.3 to 705.1 mm (27.61 to 27.77 inch) (D) 698.5 to 700.3 mm (27.50 to 27.57 inch)
Measure the gap between the top of 134-3255 Shim (7) and the lower edge of 134-3250 Bearing (1). The gap should be 7.0 mm (0.275 inch) to 10.16 mm (0.40 inch). If the measurement is not within the range, check the reference dimensions in order to determine the part that is out of tolerance. Refer to Illustration 2. Install 134-3254 Shims (6) in order to reduce the gap to a dimension that is less than 1.60 mm (0.063 inch).
Remove the Kingpost assembly. Remove the saddle cap assembly with the thrust bearing.
Install 6V-3249 Bearing (2), 134-3253 Thrust Bearing (3), and the appropriate amount of shims.
Install the swing assembly.
Install 136-6169 Kingpost Assembly (10) with 134-4078 Pinion Gear. Make sure that the timing marks are aligned.
Put 134-3243 Saddle Cap Assembly (11) in position. Install 8C-8843 Bolts (4), 8T-4223 Hard Washers (8), and 6V-8190 Nuts (13). Tighten the bolts to a torque of 920 to 1015 N m (680 to 750 lb ft). Install 6K-3632 Locknuts (5). Tighten the locknuts to a torque of 270 67 N m (200 50 lb ft).
Drill and ream the holes for 3Y-6887 Dowels (12). Install 3Y-6887 Dowels (12) so that the dowels are flush with the surface of 134-3243 Saddle Cap Assembly (1) .
Install 3B-8489 Grease Fitting (9). Apply grease to all of the bearings.
Illustration 1 g00598596
(1) 134-3250 Bearing (2) 6V-3249 Bearing (3) 134-3253 Thrust Bearing (4) 8C-8843 Bolt (5) 6K-3632 Locknut (6) 134-3254 Shim Kit (7) 134-3255 Shim (8) 8T-4223 Hard Washer (9) 3B-8489 Grease Fitting (10) 136-6169134-4078 Pinion Gear (11) 134-3243 Saddle Cap Assembly (12) 3Y-6887 Dowel (13) 6V-8190 Nut Note: Use 7M-7456 Bearing Mount Compound on all fasteners.
Insert 134-3250 Bearing (1) into 134-3243 Saddle Cap Assembly (11) .
Use the following procedure to determine the amount of shims that are needed:
Put 134-3253 Thrust Bearing (3) into the base of the casting. Put the King Post on top of the thrust bearing. Install 134-3255 Shim (7) onto the top of the shaft of 136-6169 Kingpost Assembly (10). Seat the shaft against the radius of the King Post. Make sure that the shaft is seated tightly. Do not install 6V-32493G-5337 Bearing (2) at this time.
Slip 134-3243 Saddle Cap Assembly (11) over the top shaft of the King Post. Slide the saddle cap assembly downward until the cap makes full contact with the Kingpost assembly.
Illustration 2 g00740636
(A) 355.6 mm (14.0 inch) (B) 800 mm (31.5 inch) (C) 701.3 to 705.1 mm (27.61 to 27.77 inch) (D) 698.5 to 700.3 mm (27.50 to 27.57 inch)
Measure the gap between the top of 134-3255 Shim (7) and the lower edge of 134-3250 Bearing (1). The gap should be 7.0 mm (0.275 inch) to 10.16 mm (0.40 inch). If the measurement is not within the range, check the reference dimensions in order to determine the part that is out of tolerance. Refer to Illustration 2. Install 134-3254 Shims (6) in order to reduce the gap to a dimension that is less than 1.60 mm (0.063 inch).
Remove the Kingpost assembly. Remove the saddle cap assembly with the thrust bearing.
Install 6V-3249 Bearing (2), 134-3253 Thrust Bearing (3), and the appropriate amount of shims.
Install the swing assembly.
Install 136-6169 Kingpost Assembly (10) with 134-4078 Pinion Gear. Make sure that the timing marks are aligned.
Put 134-3243 Saddle Cap Assembly (11) in position. Install 8C-8843 Bolts (4), 8T-4223 Hard Washers (8), and 6V-8190 Nuts (13). Tighten the bolts to a torque of 920 to 1015 N m (680 to 750 lb ft). Install 6K-3632 Locknuts (5). Tighten the locknuts to a torque of 270 67 N m (200 50 lb ft).
Drill and ream the holes for 3Y-6887 Dowels (12). Install 3Y-6887 Dowels (12) so that the dowels are flush with the surface of 134-3243 Saddle Cap Assembly (1) .
Install 3B-8489 Grease Fitting (9). Apply grease to all of the bearings.
Caterpillar parts catalog:
Parts cap Caterpillar catalog:
120G, 12G, 30/30, 3208, 3304, 3304B, 3306, 3306B, 517, 525C, 527, 535C, 545C, 627, 973, 973C, AP-1055D, AP-655C, BG-2455D, BG-260D, C4.4, C6.6, CS-563C, CS-573C, CS-583C, D3K2 LGP, D4E, D4E SR, D4K2 X...
3114, 3208, 3304, 3304B, AP-650B, AP-800D, C4.4, C6.6, D3K XL, D4K XL, D5K LGP, M315, M320, SCT673
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, ...
10-20B, 1090, 1190, 1190T, 1290T, 1390, 16M, 2290, 236B, 236D, 2384C, 2390, 2391, 242B3, 242D, 246C, 246D, 2484C, 2491, 24H, 24M, 252B, 256C, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 272C, 272D, 2...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M...
120M, 12M, 2470C, 3.4B IOPU, 3054, 3054B, 3054C, 3054E, 3056, 3056E, 311F LRR, 416B, 428B, 535D, 545D, 550B, 553C, 554, 559, 560B, 564, 574B, 908, 914G, 924G, 924GZ, 924H, 924HZ, 924K, 928H, 928HZ, 93...
3054, 3054B, 3054C, 3054E, 3056, 3056E, 312, 312B L, 312C, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 314E LCR, 315, 315B L, 315C, 317, 318D2 L, 320D GC, 320D L, 323D L, 330C L, 416C, 416D, 420D, 424...
1090, 1190, 1190T, 120H, 120M, 120M 2, 1290T, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14M, 160H, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16H, 16M, 216B, ...
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 323D2 L, 420E, 430E, 450E, 525D, 535D, 545D, 553C, 559, 613G, 914G, 924H, 924HZ, 924K, 928H, 928HZ, 930K, 938H, 938K, 950 GC, 953D, 963D, AP-600D, AP-655D, A...
3034583
CAP
C6.6
C6.6
3983011
CAP-TANK FILLER
336F L, 349F L, 374F L, 390F L, 525D, 535D, 545D, 555D, 725C, 730C, 770G, 770G OEM, 772G, 772G OEM, 966M, 966M XE, 972M, 972M XE, 980M, 982M, C13, C15, C18, C7.1, C9.3, M313D, M315D
336F L, 349F L, 374F L, 390F L, 525D, 535D, 545D, 555D, 725C, 730C, 770G, 770G OEM, 772G, 772G OEM, 966M, 966M XE, 972M, 972M XE, 980M, 982M, C13, C15, C18, C7.1, C9.3, M313D, M315D
3989449
CAP
336F L, 349F L, 374F L, 390F L, 621K, 623K, 627K, 770G, 770G OEM, 772G, 772G OEM, 966M, 966M XE, 972M, 972M XE, 980M, 982M, C13, C15, C18, C7.1, C9.3, D6T LGP, D6T LGPPAT, D9T
336F L, 349F L, 374F L, 390F L, 621K, 623K, 627K, 770G, 770G OEM, 772G, 772G OEM, 966M, 966M XE, 972M, 972M XE, 980M, 982M, C13, C15, C18, C7.1, C9.3, D6T LGP, D6T LGPPAT, D9T
1627677
CAP AS
C175-16, C175-20
C175-16, C175-20
1794526
CAP-PROTECTIVE
C175-16, C175-20, M318D MH, M322D MH, M325C MH
C175-16, C175-20, M318D MH, M322D MH, M325C MH
3296991
CAP
795F AC, 795F XQ, C175-16, C175-20
795F AC, 795F XQ, C175-16, C175-20
1968488
CAP-DUST
938G, 938G II, 938H, 938K, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, C175-16, IT38G, IT38G II, IT38H, IT62G
938G, 938G II, 938H, 938K, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, C175-16, IT38G, IT38G II, IT38H, IT62G
2418246
CAP
C175-16
C175-16
2418247
CAP
C175-16
C175-16
3364079
CAP-RAIN
C2.2
C2.2
3268552
CAP-RADIATOR
C2.2
C2.2
2912793
CAP-AIR
3516C, C175-16
3516C, C175-16
4205537
CAP AS
3508, 3508B, 3508C, 3512B, 3512C, 3516B, 3516C, SPF343, SPF343C, SPT343
3508, 3508B, 3508C, 3512B, 3512C, 3516B, 3516C, SPF343, SPF343C, SPT343
8W0587
CAP
3508B, 3512B, 3512C, 3516, 3516B, 3516C, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 854G, 992G, C175...
3508B, 3512B, 3512C, 3516, 3516B, 3516C, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 854G, 992G, C175...
4181880
CAP AS-FUEL FILLER
C4.4, C6.6
C4.4, C6.6