CAP 2D5790 - Caterpillar

PC Requirements
VIMSpc 2013A or later
Orderable part number: FERV0066
Dealer subscription code: JERD2138
Customer subscription code: JERD2175https://mining.cat.com/vims\ - ref. Related Links Section
VIMSpc master database v13.1.1 or laterhttps://mining.cat.com/vims\ - ref. Related Links Section
Refer to Special Instruction, REHS7337, "VIMSpc 2011a Update Release Information".
Cat ET 2013B or later
Access to Factory password system (FPS) for Telemetry and RAC. Refer to Special Instruction, REHS1238, "Obtaining Factory Passwords and Software Enabled Attachments".
PC Admin Rights are required
Full FTP access is required.Equipment Requirements
VIMSpc Cable - 305-5528 Wiring Harness (VIMS SERVICE)Com 2 Adapter or Com 3 Adapter - 275-5121 Communication Adapter As or 317-7485 Communication Adapter (3)USB to 232 Converter (Optional) - 370-8059 Adapter Kit User added IP address route deletion process - https://mining.cat.com/cda/ layout?m=122550&=7 - ref. Related Links Section.Note: The VIMS3G internal route table has changed. This process may be necessary to remove previously added routes to communicate with third-party telematics devices.New Features
Mid-precision GPS (Tracking Loop Support)
Low Precision GPS input accuracy display
Ethernet based NMEA GPS Support
Subsystem Health (Ability to upgrade to AMT without VIMS update)
Supports J1939 Diagnostics from onboard ECMsNote: Not ET service support.
Tire Pressure Monitoring – Added for future use (Added histograms and trends)
APECS Support – 793F and 797F – Added for future use (Added Histograms)
Added Transmission trend for gear shift from 6 to 7
Air Conditioner Fan Speed histogram for 795F AC
Added Snapshot for Transmission Internal Component over-speed Level 3 - 793F and 797F
Added Engine shut down Generator Phase Imbalance support for Level 3 - 795F ACMineStar Specific Features
Tope 3.0 SupportNew Improvements
VIMSpc is now able to connect the cab's VIMS3G service port (VIMS Main ECM) regardless of the VIMS Main IP address settings.
Periodic (24 hours) Orphan File Cleanup (Symptom is ceased file transfers.)
Module to Module Communications - Switched from RS485 to CANip for improved communications between Main and Application ECM.
Event Chronological List does not show Event or Diagnostic codes with Zero second durations.
TKPH/TMPH Front and Rear values do not increase even after an hour of run time, when ambient air temperature sensor is missing or not functional.
Truck Payload Calibration does not abort when strut pressures sensors are faulted.
Corrected Electrical system voltage high and low diagnostic reporting.
Improved RAC system - Pitch events correctly filtered during loading; false RAC events eliminated.
Number of low payload cycles improved
Robust FTP transfers
Ethernet Node activity improved (1 Second periodic ping to Gateway Address)
Improved Route Table to improve internal and external Ethernet activityNote: Route adds no longer necessary to integrate with third-party telematics devices.Note: A user added route delete process may be necessary to remove previously added routes to communicate with third-party telematics devices. The route delete process is available at the following website: Related Links Section: https://mining.cat.com/cda/layout?m=122550&x=7 - ref. Related Links Section.
Payload Reweigh settings for electric drive trucks now have a "Speed" configuration. Refer to Special Instruction, REHS7342, "Procedure to Configure VIMS 3G On Certain Cat® Products".MineStar Specific Improvements
Swap X and Y GPS Values and TMAC messages
Multiple TMAC messages with same date and time stamp
VIMS3G and MineStar now able to sync internal clocks and timezone. The Legacy Production Software is given in Table 1:
Table 1
Legacy