7M4048 CARBURETOR Caterpillar parts
12E, 955H, 977H
Rating:
Alternative (cross code) number:
CA7M4048
7M-4048
7M4048
CA7M4048
7M-4048
7M4048
Weight: 2 pounds 1 kg.
MOTOR GRADER, TRACK LOADER,
Information:
All Caterpillar ProductsCorrect electrical current measurements are easier to make with the new 6V4910 AC/DC Clamp-On Ammeter. The advantages of the ammeter are its small size with built in digital display, an internal (inside) power source and lower cost.
Formerly, the ammeter was large and had cable connections. It also needed an outside battery.
The ammeter is simpler to use because you do not have to break the circuit to make a current measurement. It will accept cables up to 19 mm (.75") in diameter.
... The liquid crystal digital display is accurate and easier to read than a meter with a needle.... Four AA batteries are located inside the handle of the ammeter.... The ammeter will read current from 1-500 amperes directly on the display. Above this (500-1000 A) correct the number shown according to the chart given in Special Instruction Form Number SEHS8030. Current under 1 ampere and measurements with .1 ampere resolution between .1 and 199 amperes can be measured when you connect the ammeter output to a 6V3030 Digital Multimeter, with a 6V6014 Cable (optional). The current will be read on the multimeter display.... The jaws of the ammeter open with a lever so the conductor can be inserted. These spring loaded jaws close around the conductor to measure the current.... A trigger switch will turn the ammeter on. The switch can be locked. When the turn-on trigger is released, you will be able to read the last measurement for five seconds.... The ammeter can be removed from the wire and the measurement can still be read. This feature is important in limited access areas where the display is hard to see.... This tool has a zero control for D/C operation. Some of the specifications for the 6V4910 Clamp-On Ammeter are shown in the list that follows.Complete specifications are included in the Special Instruction SEHS8030.
In addition to the basic ammeter, the following cases and tools are available to protect the tool and for use with it. They must be ordered separately.
Illustration 1. The 6V4910 Clamp-On Ammeter.
Illustration 2. In addition to the Ammeter, these items are also available.
Formerly, the ammeter was large and had cable connections. It also needed an outside battery.
The ammeter is simpler to use because you do not have to break the circuit to make a current measurement. It will accept cables up to 19 mm (.75") in diameter.
... The liquid crystal digital display is accurate and easier to read than a meter with a needle.... Four AA batteries are located inside the handle of the ammeter.... The ammeter will read current from 1-500 amperes directly on the display. Above this (500-1000 A) correct the number shown according to the chart given in Special Instruction Form Number SEHS8030. Current under 1 ampere and measurements with .1 ampere resolution between .1 and 199 amperes can be measured when you connect the ammeter output to a 6V3030 Digital Multimeter, with a 6V6014 Cable (optional). The current will be read on the multimeter display.... The jaws of the ammeter open with a lever so the conductor can be inserted. These spring loaded jaws close around the conductor to measure the current.... A trigger switch will turn the ammeter on. The switch can be locked. When the turn-on trigger is released, you will be able to read the last measurement for five seconds.... The ammeter can be removed from the wire and the measurement can still be read. This feature is important in limited access areas where the display is hard to see.... This tool has a zero control for D/C operation. Some of the specifications for the 6V4910 Clamp-On Ammeter are shown in the list that follows.Complete specifications are included in the Special Instruction SEHS8030.
In addition to the basic ammeter, the following cases and tools are available to protect the tool and for use with it. They must be ordered separately.
Illustration 1. The 6V4910 Clamp-On Ammeter.
Illustration 2. In addition to the Ammeter, these items are also available.
Caterpillar SIS machinery equipment:
Caterpillar SIS
NO. 12 MOTOR GRADER 99E00001-04490 (MACHINE) »
7M-4048
CARBURETOR
NO. 12 MTR. GRADER 99E04491-14170 (MACHINE) »
7M-4048
CARBURETOR ASSEMBLY
955 TRAXCAVATOR 60A00001-04999 (MACHINE) »
7M-4048
CARBURETOR ASSEMBLY
977 TRAXCAVATOR 53A00001-01906 (MACHINE) »
7M-4048
CARBURETOR ASSEMBLY
955 TRAXCAVATOR 60A05000-08412 (MACHINE) »
7M-4048
CARBURETOR ASSEMBLY
977 TRAXCAVATOR 53A01907-02999 (MACHINE) »
7M-4048
CARBURETOR ASSEMBLY
977 TRAXCAVATOR 53A03000-04796 (MACHINE) »
7M-4048
CARBURETOR ASSEMBLY
Caterpillar parts catalog:
Parts carburetor Caterpillar catalog:
9M3978
CARBURETOR ASSEMBLY
12E, 561B, 955H, 955K, 977H, 977K, D4D
12E, 561B, 955H, 955K, 977H, 977K, D4D
9M8059
CARBURETOR CONVERSION GROUP
12E, 955H, 977H
12E, 955H, 977H
4M4312
CARBURETOR
12E, 955H, 977H
12E, 955H, 977H
1256772
CARBURETOR GP
G3408, G3408C
G3408, G3408C
9Y4255
CARBURETOR GP
G3508, G3512
G3508, G3512
4P2009
CARBURETOR GP
G3408, G3412
G3408, G3412
4W9778
CARBURETOR GP
G3516
G3516
7W2806
CARBURETOR GP
G3408, G3412
G3408, G3412
2111689
CARBURETOR GP
G3512, G3516
G3512, G3516
9Y4359
CARBURETOR GP
G3512
G3512
2W1433
CARBURETOR GP
G3408, G3408B, G3412
G3408, G3408B, G3412
1363089
CARBURETOR GP
G3306, G3406
G3306, G3406
6L2529
CARBURETOR AND AIR TRANSFER PIPE GROUP
D342, D342C, D343, D353C, D379, D398, G342C, G379, G398
D342, D342C, D343, D353C, D379, D398, G342C, G379, G398
4P0663
CARBURETOR GP
G3508, G3512
G3508, G3512
9Y0831
CARBURETOR GP
G3412, G3412C
G3412, G3412C