CARRIER AS 1200258 - Caterpillar

1200258 CARRIER AS Caterpillar parts 994, 994D, 994F, 994H

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1200258
120-0258
1200258

Weight: 795 pounds 360 kg.

Buy CARRIER AS 1200258 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Grid Coupling Hub - Cplg Size: 1080, Bore: Solid, Material: Steel

$1,790.68

09 Apr 2022

US: Theodore's

Grid Coupling Hub - Cplg Size: 1080, Bore: Solid, Material: Steel
Generic hub diameter: 4.12 (T35-T-Hub) in, 4.81 (T31) in, 4.81 (T35-Shaft Hub) in || maximum rpm: 3600 RPM || coupling size code: 1080 || hub material: Steel || hub type: Spacer Hub

CR Seals (SKF) 1200258 - Nitrile Oil Seal - HS8 Design, Single Lip with Spring, 12.0000 in Shaft, 13.5000 in OD, 0.7500 in Width, Nitrile, HS8

$826.25

09 Apr 2022

US: Theodore's

CR Seals (SKF) 1200258 - Nitrile Oil Seal - HS8 Design, Single Lip with Spring, 12.0000 in Shaft, 13.5000 in OD, 0.7500 in Width, Nitrile, HS8
Generic shaft diameter: Especially Useful To Miinimize Lost Machine Time Where The Shaft Cannot Be Dismounted. || design type: HS8 || weight: 2.41 lb || seal type: Single Lip with Spring

LabExact 1200081 Grade CFP42 Quantitative Cellulose Filter Paper, 2.5µm, 4.25cm (Pack of 100)

$9.90

09 Apr 2022

Amazon.com

LabExact 1200081 Grade CFP42 Quantitative Cellulose Filter Paper, 2.5µm, 4.25cm (Pack of 100)
LabExact 2.5µm Quantitative filter paper 4.25cm || Cellulose

Number on catalog scheme: 31

Caterpillar 1200258 Parts scheme CARRIER AS

For full view, you need register

Compatible equipment models: 1200258:

WHEEL LOADER 994 994D 994F 994H Caterpillar

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 -
B - Loctie 263 -
C 0S-2318 Bolt 8 Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Remove the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Personal injury can result from driveline torque windup under load.Unequal wheel speed can result in driveline torque windup which can cause driveline components to be under load during disassembly.Relieve the driveline torque windup before disassembly.
Illustration 1 g01074389
Support rear drive shaft (1). Remove four bolts (2) and four bolts (3).
Use two people to remove rear drive shaft (1). The weight of the rear drive shaft is approximately 27 kg (60 lb). Installation Procedure
When the rear drive shaft is installed, it must be installed in phase with the rear axle assembly yoke. The rear drive shaft must be installed in phase with the center and front drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned.
Illustration 2 g01074389
Use two people to position rear drive shaft (1) between the output yoke of the output transfer gears and the rear differential. The weight of the rear drive shaft is approximately 27 kg (60 lb).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (2) prior to installation. Note: Bolts (2) are single use only parts. Discard bolts (2) whenever loosened.
Install bolts (2). Tighten bolts (2) to a torque of 300 30 N m (220 20 lb ft).
Apply Tooling (A) and then apply Tooling (B) to the threads of bolts (3) prior to installation. Note: Bolts (3) are single use only parts. Discard bolts (3) whenever loosened.
Install bolts (3). Tighten bolts (3) to a torque of 300 30 N m (220 20 lb ft). End By:
Install the transmission bottom guard. Refer to Disassembly and Assembly, "Bottom Guard (Transmission) - Remove and Install".
Remove the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".