AVSPARE.COM
parts catalog

CARRIER-STATOR 6Y7197 - Caterpillar


6Y7197 CARRIER-STATOR Caterpillar parts 994, 994F, 994H
Rating:
26
Alternative (cross code) number:
CA6Y7197
6Y-7197
6Y7197
Caterpillar 6Y7197 CARRIER-STATOR
Weight: 113 pounds 51 kg.

Buy CARRIER-STATOR 6Y7197 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 6Y7197:

WHEEL LOADER  994   994F   994H   Caterpillar
Number on catalog scheme: 7
  For full view, you need register

Information:


Illustration 1 g06033141Adjustment Procedure (Off Machine)
Place wheel spindle (1) on a support (or floor) with the small end up.
Lubricate the wheel bearings with the lubricant that is being sealed.
Assemble brake group (6), wheel assembly (2), hub (3) and the wheel bearings on wheel spindle (1).
Install bearing plate (5) without shims (7).
Illustration 2 g06033146
Apply clean final drive oil to the threads of five bolts (4) prior to installation.
Install five bolts (4) evenly spaced, but do not tighten.
Use a depth micrometer to measure the distance from the top of bearing plate (5) to wheel spindle (1). Measure through three evenly spaced small holes in bearing plate (5). Find the average value of the three measurements. This average is the zero reading.Note: Mark the holes used for the measurements.
Tighten bolts (4) to a torque of 90 14 N m (66 10 lb ft).
Turn wheel assembly (2) two to three complete revolutions.
Loosen bolts (4) until bearing plate (5) is loose.
Turn wheel assembly (2) two to three complete revolutions.
Use a depth micrometer again to measure the distance from the top of bearing plate (5) to wheel spindle (1). Measure through the three marked holes in bearing plate (5). Find the average value of the three measurements.
Compare the average measurement from Step 12 to the zero reading from Step 7. If, the difference is 0.05 mm (0.002 inch) or less go to Step 15. If the difference is greater than 0.05 mm (0.002 inch), repeat Steps 8 through 12, then go to Step 14.
If, the measurement found at Step 13 is still greater than 0.05 mm (0.002 inch) disassemble the parts to determine the problem. If the measurement is 0.05 mm (0.002 inch) or less, go to Step 15.
Tighten bolts (4) to a torque of 40 7 N m (30 5 lb ft).
Turn the wheel assembly two to three complete revolutions.
Retighten bolts (4) to a torque of 40 7 N m (30 5 lb ft).
Use a depth micrometer to measure the distance from the top of bearing plate (5) to wheel spindle (1). Measure through the three marked holes in the bearing plate (5). Calculate the average value of the three measurements.
Remove bolts (4) and bearing plate (5) from wheel spindle (1).
Use an outside micrometer to measure the thickness of bearing plate (5). Make a measurement at each of the three marked holes that were used for the depth measurement. Find the average value of the three measurements.
Subtract the average thickness of retainer (5) found in Step 20 from the value found in Step 18. This difference is the clearance between the end of spindle housing (1) and retainer (5).
Add 0.10 mm (0.004 inch) to the value found in Step 21 to determine the thickness of shims (7) that are required.
Apply Loctite 7649 and then apply Loctite 263 to bolts (4).
Install the required shims (7), bearing plate (5) and bolts (4) to wheel spindle (1).
Tighten bolts (4) to a torque of 270 25 N m (200 20 lb ft).

Caterpillar parts catalog:

Caterpillar parts catalog
994K Wheel Loader SMX00001-UP (MACHINE) POWERED BY 3516 Engine
994K Wheel Loader MM900001-UP (MACHINE) POWERED BY 3516B Engine
994 Wheel Loader 9YF00001-UP (MACHINE) POWERED BY 3516 Engine
994F Wheel Loader 44200001-UP (MACHINE) POWERED BY 3516 Engine
994H Wheel Loader DWC00001-UP (MACHINE) POWERED BY 3516B Engine
994K Wheel Loader MRK00001-UP (MACHINE) POWERED BY 3516B Engine


Parts carrier Caterpillar catalog:

6Y6606 CARRIER AS
994, 994D, 994F, 994H
1150767 CARRIER-PLANETARY
993K, 994, 994D, 994F, 994H, D11R, D11T
1150761 CARRIER AS
844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K, 993K, 994, 994D, 994F, 994H, D11R, D11T
1938609 CARRIER-PLANETARY
844H, 990H, 993K, 994, 994D, 994F, 994H, D11R, D11T
7T1838 CARRIER-STATOR
789, 789B, 793, 793B, 994
1165812 CARRIER-STATOR
789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 994
8R5960 CARRIER-PLANETARY
994, 994D, 994F, 994H
1165812 CARRIER-STATOR
789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 994
7T1838 CARRIER-STATOR
789, 789B, 793, 793B, 994
1938609 CARRIER-PLANETARY
844H, 990H, 993K, 994, 994D, 994F, 994H, D11R, D11T
1150761 CARRIER AS
844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K, 993K, 994, 994D, 994F, 994H, D11R, D11T
1150767 CARRIER-PLANETARY
993K, 994, 994D, 994F, 994H, D11R, D11T
9U0473 CARRIER AS-DIFFERENTIAL
824C, 980F, 980F II, R1700 II
1T1522 CARRIER AS
950B, 950B/950E, 950F
9W4949 CARRIER-PLANETARY
950B, 950B/950E, 950F, 950F II, 966R, R1300, R1300G
8R5960 CARRIER-PLANETARY
994, 994D, 994F, 994H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.