7K5057 CARRIER AND LINING ASSEM. Caterpillar parts
528, 613, 930, 950
Rating:
Alternative (cross code) number:
CA7K5057
7K-5057
7K5057
CA7K5057
7K-5057
7K5057
Weight: 2 pounds 1 kg.
WHEEL LOADER, WHEEL TRACTOR,
You can buy:
US$51.45
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Reliable Aftermarket Parts Our Name Says It All, 8R0821 7K5057 Brake Pad Fits CAT Fits Caterpillar 613 613B 950 IT12
Reliable Aftermarket Parts 7 Inch Zirconia heavy duty, durable, X-weight polyester cloth sanding discs || Faster cutting and longer life than standard Aluminum Oxide discs || Premium Aluminum Zirconia/Aluminum Oxide blend abrasive grain || Hook & Loop disc grips to the appropriate backup pad attached to an orbital or DA sander || High quality German industrial abrasives factory direct
Reliable Aftermarket Parts 7 Inch Zirconia heavy duty, durable, X-weight polyester cloth sanding discs || Faster cutting and longer life than standard Aluminum Oxide discs || Premium Aluminum Zirconia/Aluminum Oxide blend abrasive grain || Hook & Loop disc grips to the appropriate backup pad attached to an orbital or DA sander || High quality German industrial abrasives factory direct
Stevens Lake Parts One New Brake Pad Carrier Lining Fits CAT, Fits Caterpillar 613, 613B, 950, IT12 Models Interchangeable with 2V9135, 2V9135-A, 7K5057, 8R0821, 8R0821-A
Stevens Lake Parts Brake Pads Used In Sets Of Two. || For The Complete Brake Pad Set, Order 2 From This Listing. || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Stevens Lake Parts Brake Pads Used In Sets Of Two. || For The Complete Brake Pad Set, Order 2 From This Listing. || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
This part in 2 request:
Show.
This information for suppliers only!
2020-01-08
2020-01-08
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 7K5057:
Information:
Remove Water Temperature Regulators
start by:a) remove fuel filter housing1. Remove the clamps to remove the fuel lines from the water temperature regulator housings and remove the plate on top of the oil filter housing. 2. Disconnect tube (1) from the regulator housings and the aftercooler adapter. Remove the tube from the engine. 3. Fasten a hoist to water temperature regulator housings (2) as shown. Remove the bolts that hold housings (2) to water manifolds (3) and brackets (4). Remove the housings from the engine. The weight of housings (2) is 49 kg (108 lb.). 4. Remove the bolts and remove housing (5) from the water temperature regulators. 5. Remove regulators (6) from the housing. 6. If necessary, remove seals (8) from the housing.7. Remove ferrule (7) and the ball from the housing necessary.Install Water Temperature Regulators
1. If the ball and ferrule were removed, install the ball and use tooling (A) to install the ferrule until it makes contact with the bottom of the bore. Make sure the open end of the ferrule is toward the outside of the housing. 2. If the seals were removed, use tooling (A) to install the seals in the housing. Make sure the lip of the seal is toward the inside of the housing as shown.
If the water temperature regulators are installed wrong, it will cause the engine to overheat.
3. Install water temperature regulators (1) in the housing with the spring up as shown. 4. Put housing (2) and the gasket in position on the regulators. Install the bolts to hold the housing in position. 5. Fasten a hoist to water temperature regulator housings (3) and put the housings and gaskets in position on the engine. Install the bolts to hold the housings to water manifolds (5) and brackets (4).6. Install the tube between the aftercooler adapter and the regulator housings.7. Put the plate on top of the oil lifter housing and install the bolts. Install the fuel lines and the clamps on the water temperature regulator housings.end by:a) install fuel filter housing
start by:a) remove fuel filter housing1. Remove the clamps to remove the fuel lines from the water temperature regulator housings and remove the plate on top of the oil filter housing. 2. Disconnect tube (1) from the regulator housings and the aftercooler adapter. Remove the tube from the engine. 3. Fasten a hoist to water temperature regulator housings (2) as shown. Remove the bolts that hold housings (2) to water manifolds (3) and brackets (4). Remove the housings from the engine. The weight of housings (2) is 49 kg (108 lb.). 4. Remove the bolts and remove housing (5) from the water temperature regulators. 5. Remove regulators (6) from the housing. 6. If necessary, remove seals (8) from the housing.7. Remove ferrule (7) and the ball from the housing necessary.Install Water Temperature Regulators
1. If the ball and ferrule were removed, install the ball and use tooling (A) to install the ferrule until it makes contact with the bottom of the bore. Make sure the open end of the ferrule is toward the outside of the housing. 2. If the seals were removed, use tooling (A) to install the seals in the housing. Make sure the lip of the seal is toward the inside of the housing as shown.
If the water temperature regulators are installed wrong, it will cause the engine to overheat.
3. Install water temperature regulators (1) in the housing with the spring up as shown. 4. Put housing (2) and the gasket in position on the regulators. Install the bolts to hold the housing in position. 5. Fasten a hoist to water temperature regulator housings (3) and put the housings and gaskets in position on the engine. Install the bolts to hold the housings to water manifolds (5) and brackets (4).6. Install the tube between the aftercooler adapter and the regulator housings.7. Put the plate on top of the oil lifter housing and install the bolts. Install the fuel lines and the clamps on the water temperature regulator housings.end by:a) install fuel filter housing
Cat SIS web machinery list:
Parts carrier Caterpillar catalog:
518, 920, 930, 950, 966C
120G, 12G, 130G, 14G, 16G, 920, 930, 966C
518, 930, 930R
613, 950
518, 613, 613B, 950
528, 613B, 815, 950, 950B, 950B/950E, 966C, D25C, D30C, D350C, D35C, D35HP, D400
930, 950
528, 920
920, 926, 930
518, 930
528, 814, 815, 966C
518C, 528, 528B, 530B, 814, 815, 816
3S2656
CARRIER
621, 623, 627, 631C, 657B
621, 623, 627, 631C, 657B
2S6497
CARRIER
621, 657B
621, 657B
2S7829
CARRIER
637B, 641B, 650B
637B, 641B, 650B
621, 627, 631C
518, 930, 930R
7S8498
CARRIER ASSEM.
920, 930
920, 930
6D6574
CARRIER
650B
650B
6D6582
CARRIER ASSEM.
650B, 777
650B, 777
518, 528, 910, 920
6D9505
CARRIER ASSEM.
641B, 650B, 657B
641B, 650B, 657B
518, 930, 930R