9W3083 CARRIER-PLANETARY Caterpillar parts
776C, 776D, 777B, 777D, 777F, 777G
Rating:
Alternative (cross code) number:
CA9W3083
9W-3083
9W3083
CA9W3083
9W-3083
9W3083
Weight: 67 pounds 30 kg.
TRACTOR, TRUCK,
This part in 2 request:
Show.
This information for suppliers only!
2022-12-02
2016-06-16
Information:
Machine ECM
The following is a list of diagnostic codes (SPN) that are associated with the relays of the machine.
Table 1
Machine ECM (MID 39)
SPN-FMI Code Description System Response
818-14 Master Control Relay: Special Instruction De-energize Relay
Fault Level - 1 A relay is a component that uses a small amount of electrical current to control the state of a circuit. The circuit is either opened or closed. Possible causes for an FMI 14 diagnostic code are:
A short to ground exists.
The supply circuit is open.
The return circuit is open.
The relay has failed.
The ECM has failed. A failure of the ECM is unlikely.
Illustration 1 g03828529
Schematic of the relay circuits
Note: The diagram above is a simplified schematic of the Machine ECM connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR6464 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring harness for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.
Table 2
FMI 14 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Return Circuit For A Short To Ground
A. Turn key switch and disconnect switch OFF.
B. Disconnect the Relay from the machine harness.
C. Disconnect the machine harness connectors from the ECM.
D. At the ECM machine harness connector, measure the resistance between the signal contact and all other contacts that are used in the ECM.
Each resistance measurement is greater than 5K Ω. OK - Each resistance measurement is greater than 5K Ω. The machine harness is correct.
Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5K Ω. A short circuit exists between the signal circuit and the circuit with the low resistance measurement.
Repair: Repair or replace the machine harness.
Note: A resistance that is greater than 5 Ω but less than 5K Ω would indicate a loose connection or a corroded connection in the circuit. A resistance measurement that is greater than 5K Ω would indicate an open in the circuit.
Proceed to Test Step 3.
2. Check The Harness For An Open
A. The key start switch and disconnect switch remain in the OFF position.
B. The the machine harness connectors remain disconnected from the ECM.
C. Place a jumper wire between the Signal wire and the Signal return.
D. At the ECM machine harness connector, measure the resistance between the signal contact and the return contact.
The resistance is less than 5 Ω. OK - The resistance is less than 5Ω. The machine harness is correct.
Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 Ω. The resistance measurement is not correct. There is an open circuit in
The following is a list of diagnostic codes (SPN) that are associated with the relays of the machine.
Table 1
Machine ECM (MID 39)
SPN-FMI Code Description System Response
818-14 Master Control Relay: Special Instruction De-energize Relay
Fault Level - 1 A relay is a component that uses a small amount of electrical current to control the state of a circuit. The circuit is either opened or closed. Possible causes for an FMI 14 diagnostic code are:
A short to ground exists.
The supply circuit is open.
The return circuit is open.
The relay has failed.
The ECM has failed. A failure of the ECM is unlikely.
Illustration 1 g03828529
Schematic of the relay circuits
Note: The diagram above is a simplified schematic of the Machine ECM connections. The schematic is electrically correct. However, not all of the possible harness connectors are shown. Refer to the latest revision of Electrical Schematic, UENR6464 for the complete schematic.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in this circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. Check the wiring harness for pinch points or abrasions. Look for and repair areas that indicate wires are exposed. If a problem with a connection is found, correct the problem and verify that the diagnostic code is active before performing a troubleshooting procedure.
Table 2
FMI 14 Troubleshooting
Troubleshooting Test Steps Values Results
1. Check The Return Circuit For A Short To Ground
A. Turn key switch and disconnect switch OFF.
B. Disconnect the Relay from the machine harness.
C. Disconnect the machine harness connectors from the ECM.
D. At the ECM machine harness connector, measure the resistance between the signal contact and all other contacts that are used in the ECM.
Each resistance measurement is greater than 5K Ω. OK - Each resistance measurement is greater than 5K Ω. The machine harness is correct.
Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5K Ω. A short circuit exists between the signal circuit and the circuit with the low resistance measurement.
Repair: Repair or replace the machine harness.
Note: A resistance that is greater than 5 Ω but less than 5K Ω would indicate a loose connection or a corroded connection in the circuit. A resistance measurement that is greater than 5K Ω would indicate an open in the circuit.
Proceed to Test Step 3.
2. Check The Harness For An Open
A. The key start switch and disconnect switch remain in the OFF position.
B. The the machine harness connectors remain disconnected from the ECM.
C. Place a jumper wire between the Signal wire and the Signal return.
D. At the ECM machine harness connector, measure the resistance between the signal contact and the return contact.
The resistance is less than 5 Ω. OK - The resistance is less than 5Ω. The machine harness is correct.
Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 Ω. The resistance measurement is not correct. There is an open circuit in
Caterpillar parts catalog:
Parts carrier Caterpillar catalog:
6P7705
CARRIER-RING
24H, 24M, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 641B, 651E, 657E, 657G, 776C, 776D, 777, 777B, 777D, 777F, 777G, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 8...
24H, 24M, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 641B, 651E, 657E, 657G, 776C, 776D, 777, 777B, 777D, 777F, 777G, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 8...
1996019
CARRIER-PLANETARY
776D, 777D, 777F
776D, 777D, 777F
3201232
CARRIER-RING
773G, 773G OEM, 775G, 775G OEM, 777D, 777F, 777G
773G, 773G OEM, 775G, 775G OEM, 777D, 777F, 777G
3201231
CARRIER-STATOR
773G, 773G OEM, 775G, 775G OEM, 777D, 777F, 777G
773G, 773G OEM, 775G, 775G OEM, 777D, 777F, 777G
2822482
CARRIER-PLANETARY
777F, 777G
777F, 777G
2662092
CARRIER AS-DIFFERENTIAL
777F, 777G
777F, 777G
2662093
CARRIER AS-DIFFERENTIAL
777F, 777G
777F, 777G
3780981
CARRIER-PLANETARY
777D, 777G
777D, 777G
1T1245
CARRIER
777, 777B, 785
777, 777B, 785
1T1529
CARRIER-STATOR
777B, 785
777B, 785
1T1554
CARRIER-CLUTCH
777B, 785
777B, 785
9W8442
CARRIER-PLANETARY
776C, 776D, 777B, 777D, 777F, 777G
776C, 776D, 777B, 777D, 777F, 777G
3T3073
CARRIER-PLANETARY
776C, 776D, 777B, 777D
776C, 776D, 777B, 777D
1049406
CARRIER AS-DIFFERENTIAL
776C, 776D, 777D
776C, 776D, 777D
5T7839
CARRIER AS-DIFFERENTIAL
776C, 777
776C, 777
2G6203
CARRIER-PLANETARY
776C, 776D, 777, 777B, 777D
776C, 776D, 777, 777B, 777D
8W3004
CARRIER AS-INNER
784B, 784C, 785, 785B, 785C, 785D
784B, 784C, 785, 785B, 785C, 785D
8W1365
CARRIER-PLANETARY
784B, 785, 785B, 789, 789B
784B, 785, 785B, 789, 789B
1096534
CARRIER AS-DIFFERENTIAL
784B, 785B
784B, 785B
5T9058
CARRIER AS-DIFFERENTIAL
784B, 785, 785B
784B, 785, 785B
1T1819
CARRIER-CLUTCH
776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D
776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D