9W6043 CARRIER Caterpillar parts
Rating:
Alternative (cross code) number:
CA9W6043
9W-6043
9W6043
CA9W6043
9W-6043
9W6043
Information:
Adjustment Procedure For Preload Of Oil Pump Drive Bearings
1. Install gear (6), bearing assembly (7) and shaft (8) into the housing without shims (14).2. Tighten four bolts (15) evenly to a torque of ... 7 1 N m (60 9 lb in)3. Measure the distance between the housing and shaft (8) at three locations.4. Make and install a thickness of shims (15) the same thickness as the average distance measured minus ... 0.14 mm (.004 in)5. Install gears (1) and (10), bearings (2) and (13) and cages (4) and (12) without seals or shims (3) and (9). Tighten bolts (5) and (11) in cages (4) and (12) evenly until a small resistance is felt in rotation.6. Measure the distance between the housing and cage (4) and the housing and cage (12) in three places.7. Make and install a thickness of shims (3) and shims (9) the same thickness as the average distance measured plus ... 0.10 mm (.004 in) Install a small amount of the lubricant on the seals and in the bore of the cages before the O-ring seals are installed.8. The end play of gears (1) and (10) must be ... 0.05 to 0.15 mm (.002 to .006 in)
After assembly, put .95 liter (1 U.S. quart) of SAE 10W oil in the oil pump drive housing before the engine is started.
1. Install gear (6), bearing assembly (7) and shaft (8) into the housing without shims (14).2. Tighten four bolts (15) evenly to a torque of ... 7 1 N m (60 9 lb in)3. Measure the distance between the housing and shaft (8) at three locations.4. Make and install a thickness of shims (15) the same thickness as the average distance measured minus ... 0.14 mm (.004 in)5. Install gears (1) and (10), bearings (2) and (13) and cages (4) and (12) without seals or shims (3) and (9). Tighten bolts (5) and (11) in cages (4) and (12) evenly until a small resistance is felt in rotation.6. Measure the distance between the housing and cage (4) and the housing and cage (12) in three places.7. Make and install a thickness of shims (3) and shims (9) the same thickness as the average distance measured plus ... 0.10 mm (.004 in) Install a small amount of the lubricant on the seals and in the bore of the cages before the O-ring seals are installed.8. The end play of gears (1) and (10) must be ... 0.05 to 0.15 mm (.002 to .006 in)
After assembly, put .95 liter (1 U.S. quart) of SAE 10W oil in the oil pump drive housing before the engine is started.
Parts carrier Caterpillar catalog:
9W4177
CARRIER AS
Caterpillar
Caterpillar
9W3376
CARRIER
Caterpillar
Caterpillar
9W0796
CARRIER
Caterpillar
Caterpillar
9W0336
CARRIER-PLANET
Caterpillar
Caterpillar
9V1259
CARRIER
Caterpillar
Caterpillar
9U9852
CARRIER
Caterpillar
Caterpillar
9Y0270
CARRIER-GOV DR
Caterpillar
Caterpillar
9X1548
CARRIER
Caterpillar
Caterpillar
9W8244
CARRIER AS
Caterpillar
Caterpillar