CARTRIDGE GP-TURBOCHARGER 0R7165 - Caterpillar

0R7165 CARTRIDGE GP-TURBOCHARGER Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA0R7165
0R-7165
0R7165

Caterpillar 0R7165 CARTRIDGE GP-TURBOCHARGER

Weight: 23 pounds 10 kg.

Buy CARTRIDGE GP-TURBOCHARGER 0R7165 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:

1004095 CARTRIDGE GP -A 0R7165 R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Molloparts Turbocharger Cartridge 1004095 100-4095 0R680 0R7165 0R-7165 7W3570 CA1004095 CA0R7165 Compatible with Caterpillar Engine 3512 3516 G3516 PM3512 G3412 3512B 3516B

$1,435.00

21 Aug 2024
24.0[10.80] Pounds
CN: Molloparts

Molloparts Turbocharger Cartridge 1004095 100-4095 0R680 0R7165 0R-7165 7W3570 CA1004095 CA0R7165 Compatible with Caterpillar Engine 3512 3516 G3516 PM3512 G3412 3512B 3516B
Molloparts Part Number: 1004095 100-4095 0R680 0R7165 0R-7165 7W3570 CA1004095 CA0R7165 || Compatible with Caterpillar Engine 3512 3516 G3516 PM3512 G3412 3512B 3516B || Package Included: 1 x Turbocharger Cartridge || Easy Installation.Stable Characteristics High Reliability || It Is a Replacement Part Not Original Part. But It Can Work Good For You

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#1206592 0R7165

2023-09-14

For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Tap 7/8-9 NC 1
B 1A-5576 Bolt 1
8C-6913 Hard Washer 7
C 221-9803 Rubber Stopper 1
D 1P-0510 Driver Gp 1
E 4C-5552 Large Bore Brush 1
F 4C-9507 Retaining Compound 1 Start By:
Remove the unit injectors.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
Illustration 1 g02163825
Position Tooling (C) at the bottom of the unit injector sleeve (1).
Coat Tooling (A) (not shown) with clean grease. Use Tooling (A) to cut threads into unit injector sleeve (1).
Use Tooling (B) in order to remove unit injector sleeve (1). Discard the unit injector sleeve (1). Installation Procedure
Thoroughly clean the bores for the unit injectors with Tooling (E).
Illustration 2 g02164118
Apply clean engine oil to O-ring seals (2). Install O-ring seals (2) on unit injector sleeve (1).
Apply a thin coating of Tooling (F) around the outer circumference of unit injector sleeve (1) at Area (G).
Position unit injector sleeve (1) in the cylinder head. Use a hammer and Tooling (D) in order to install unit injector sleeve (1) in the cylinder head. Note: Allow Tooling (F) to cure for 2 hours at 21 °C (70 °F) before filling the engine with fuel or coolant. Longer curing time is required for lower temperatures.
Fill the cooling system with coolant to the correct level. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations". End By:
Install the unit injectors.