1J0784 CARTRIDGE Caterpillar parts
46
Rating:
Alternative (cross code) number:
CA1J0784
1J-0784
1J0784
CA1J0784
1J-0784
1J0784
Weight: 20 pounds 9 kg.
HYDRAULIC CONTROL,
Compatible equipment models: 1J0784:
Number on catalog scheme:
For full view, you need register
Information:
Operation Description:During the installation of a Product Link module, the wiring harness is connected to the existing CAT data link wiring on the machine. If this is not done properly, the continuity of the CAT data link wiring may be open intermittently. This condition may not be apparent immediately. This will cause a problem when you are trying to connect the Electronic Technician (ET) to the machine.
The ET may report that no ECM has been found.
The ET may not report every ECM that is on the machine.
The ET may report an ECM but the ECM will not have any data.If the wires for the data link are reversed during the installation, the Product Link ECM will not be shown after connecting the ET to the machine.Test Step 1. VERIFY THAT THE DATA LINK WIRES ARE NOT REVERSED.
Check that the positive data link wire (893-GN) in the wiring harness for the Product Link is connected to the positive wire in the machine harness for the machine.
Check that the negative data link wire (892-BR) in the wiring harness for the Product Link is connected to the negative wire in the machine harness.Expected Result:The data link wires are properly connected.Results:
OK - The data link wires are properly connected. Proceed to Test Step 2.
NOT OK - The wires for the data link are reversed.Repair: Reinstall the data link wires correctly and check the operation of the Product Link module by using the ET. Stop.Test Step 2. CHECK THE WIRING WITH A MULTIMETER.
Turn off the machine and turn the disconnect switch to the OPEN position.
Measure the resistance of the negative data link wire from the service connector (contact "E") to the location for the spliced data link wire. Note the resistance.
Measure the resistance of the positive data link wire from the service connector (contact "D") to the location for the spliced data link wire. Note the resistance.Expected Result:The resistance in both wires is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. Repair the wiring harness.Repair: After repairing, resume the setup procedures for the installation of the Product Link. Stop.Test Step 3. VERIFY THAT THE WIRING FOR THE CAT DATA LINK IS PROPERLY CONNECTED.
Check the spliced connections for the data link that were made during the installation. Verify that all connections are clean and tight.
Reconnect the harness connectors that were disturbed during the installation. Ensure that all of the pins are correctly seated in the sockets.
Reconnect the cable from the service tool connector. Attempt to access the data link by using the ET.Expected Result:The Electronic Technician lists the electronic control modules that are available on the machine. The ECM for the Product Link can be accessed.Results:
OK - The Electronic Technician lists the electronic control modules that are available on the machine. The ECM for the Product Link can be accessed. Resume the setup procedures for the installation of the Product Link. Stop.
NOT OK - The Electronic
The ET may report that no ECM has been found.
The ET may not report every ECM that is on the machine.
The ET may report an ECM but the ECM will not have any data.If the wires for the data link are reversed during the installation, the Product Link ECM will not be shown after connecting the ET to the machine.Test Step 1. VERIFY THAT THE DATA LINK WIRES ARE NOT REVERSED.
Check that the positive data link wire (893-GN) in the wiring harness for the Product Link is connected to the positive wire in the machine harness for the machine.
Check that the negative data link wire (892-BR) in the wiring harness for the Product Link is connected to the negative wire in the machine harness.Expected Result:The data link wires are properly connected.Results:
OK - The data link wires are properly connected. Proceed to Test Step 2.
NOT OK - The wires for the data link are reversed.Repair: Reinstall the data link wires correctly and check the operation of the Product Link module by using the ET. Stop.Test Step 2. CHECK THE WIRING WITH A MULTIMETER.
Turn off the machine and turn the disconnect switch to the OPEN position.
Measure the resistance of the negative data link wire from the service connector (contact "E") to the location for the spliced data link wire. Note the resistance.
Measure the resistance of the positive data link wire from the service connector (contact "D") to the location for the spliced data link wire. Note the resistance.Expected Result:The resistance in both wires is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. Repair the wiring harness.Repair: After repairing, resume the setup procedures for the installation of the Product Link. Stop.Test Step 3. VERIFY THAT THE WIRING FOR THE CAT DATA LINK IS PROPERLY CONNECTED.
Check the spliced connections for the data link that were made during the installation. Verify that all connections are clean and tight.
Reconnect the harness connectors that were disturbed during the installation. Ensure that all of the pins are correctly seated in the sockets.
Reconnect the cable from the service tool connector. Attempt to access the data link by using the ET.Expected Result:The Electronic Technician lists the electronic control modules that are available on the machine. The ECM for the Product Link can be accessed.Results:
OK - The Electronic Technician lists the electronic control modules that are available on the machine. The ECM for the Product Link can be accessed. Resume the setup procedures for the installation of the Product Link. Stop.
NOT OK - The Electronic
Caterpillar parts catalog:
Parts cartridge Caterpillar catalog:
4H2087
CARTRIDGE
172, 46
172, 46
3J8335
CARTRIDGE ASSEM.
172, 46
172, 46
4H2087
CARTRIDGE
172, 46
172, 46