1W9573 CARTRIDGE GP-TURBOCHARGER Caterpillar parts
992C
Rating:
Alternative (cross code) number:
CA1W9573
1W-9573
1W9573
CA1W9573
1W-9573
1W9573
Weight: 23 pounds 10 kg.
WHEEL LOADER,
Compatible equipment models: 1W9573:
Number on catalog scheme:
4
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 307-6498 Tool 1
B 138-7575 Link Bracket 1 Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release". Note: Cleanliness is an important factor. Before the removal procedure, thoroughly clean the exterior of the component. Thoroughly cleaning the exterior of the component will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses, and all tubes in order to prevent fluid loss and contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g01150559
Remove cover (1).
Discharge the nitrogen gas from the brake accumulator. Reference: Refer to Special Instruction, REHS5464, "Accumulator Discharge and Charging Procedures".
Illustration 2 g03381101
Remove two bolts (2) and guard (3).
Illustration 3 g01150561
Typical example
Install Tooling (A), Tooling (B), and a suitable lifting device to brake accumulator (4). The weight of brake accumulator (4) is approximately 38 kg (84 lb).
Disconnect hose assembly (7).
Remove bolt (5) and the nut from clamp (6).
Remove brake accumulator (4).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 307-6498 Tool 1
B 138-7575 Link Bracket 1 Start By:
Install the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Remove and Install".
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release". Note: Cleanliness is an important factor. Before the removal procedure, thoroughly clean the exterior of the component. Thoroughly cleaning the exterior of the component will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses, and all tubes in order to prevent fluid loss and contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Illustration 1 g01150559
Remove cover (1).
Discharge the nitrogen gas from the brake accumulator. Reference: Refer to Special Instruction, REHS5464, "Accumulator Discharge and Charging Procedures".
Illustration 2 g03381101
Remove two bolts (2) and guard (3).
Illustration 3 g01150561
Typical example
Install Tooling (A), Tooling (B), and a suitable lifting device to brake accumulator (4). The weight of brake accumulator (4) is approximately 38 kg (84 lb).
Disconnect hose assembly (7).
Remove bolt (5) and the nut from clamp (6).
Remove brake accumulator (4).
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts cartridge Caterpillar catalog:
992C, D8L
992C, 992D
6T6098
CARTRIDGE
988B, 992C, D10, D9L
988B, 992C, D10, D9L
D350E, D400E, D8L, D9N
992C, D8L
613C, 613C II, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816B, 816F, 816F II
966D, 966F, 966F II, 970F, R1600, R1600G, R1600H
D10N, D9L
992C, 992D