CARTRIDGE ASSEM. 3S4009 - Caterpillar

3S4009 CARTRIDGE ASSEM. Caterpillar parts 955H

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3S4009
3S-4009
3S4009

Weight: 22 pounds 9 kg.

Buy CARTRIDGE ASSEM. 3S4009 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Related part:

3S4009 CARTRIDGE GP 0R5876 R

Compatible equipment models: 3S4009:

TRACK LOADER 955H Caterpillar

Number on catalog scheme: None

Caterpillar 3S4009 Parts scheme CARTRIDGE ASSEM.

For full view, you need register

Information:

Removal Procedure
Start By:
If necessary, remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.
Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold - Remove" for the correct procedure.
Remove the Electronic Control Module (ECM) mounting bracket. Refer to Disassembly and Assembly, "ECM Mounting Bracket - Remove and Install" for the correct procedure.
Remove the boost pressure sensor. Refer to Disassembly and Assembly, "Boost Pressure Sensor - Remove and Install" for the correct procedure.
Remove the air inlet temperature sensor. Refer to Disassembly and Assembly, "Inlet Air Temperature Sensor - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the engine is equipped, with a cover over the fuel system the cover will need to be removed.
Disconnect the breather hose from the separator for the crankcase breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.
Illustration 1 g01335890
Cut the cable straps that secure the harness assembly to inlet manifold (4). Position the harness assembly away from the inlet manifold.
Remove bolts (1) from inlet connection (2).
Remove inlet connection (2) and gasket (3) from inlet manifold (4).
Remove bolts (5).
Remove inlet manifold (4) from the cylinder head. Use a suitable tool to pry the inlet manifold from the cylinder head. Use the recess at Position (X) to pry the inlet manifold.
Remove inlet manifold seal (6) from the recess in inlet manifold (4).
Do not remove two dowel pins (7). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 2431 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01335909
Ensure that the inlet manifold is clean and free from damage. If necessary, replace the inlet manifold. If a new inlet manifold is installed, install two new dowel pins (7) to inlet manifold (4). Note: Do not install dowel pins to the cylinder head.
Clean the gasket surface of the cylinder head.
Align tag (8) to the slot at Position (Y) on the inlet manifold. Install new seal (6) to the groove in inlet manifold (4). Ensure that the seal is correctly located.
Align dowel pins (7) to the holes in the cylinder head. Install inlet manifold (4) to the cylinder head.
Apply Tooling (A) to bolts (5). Install the bolts to inlet manifold (4).
Illustration 3 g01335892
Tighten the bolts to a torque of 22 N m (16 lb ft) in the sequence that is shown in Illustration 3.
Ensure that inlet connection (2) is clean and free from damage. If necessary, replace the inlet connection.
Position a new gasket (3) onto the inlet manifold. Install inlet connection (2) to inlet manifold (4).
Install bolts (1) to inlet connection (2). Tighten the bolts to a torque of 22 N m (16 lb ft).
Install the air temperature sensor. Refer to Disassembly and Assembly, "Inlet Air Temperature Sensor - Remove and Install" for the correct procedure.
Install the boost pressure sensor. Refer to Disassembly and Assembly, "Boost Pressure Sensor - Remove and Install" for