7J0574 CARTRIDGE ASSEM. Caterpillar parts
621B, 623B, 992
Rating:
Alternative (cross code) number:
CA7J0574
7J-0574
7J0574
CA7J0574
7J-0574
7J0574
Weight: 13 pounds 6 kg.
WHEEL LOADER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
HpaErtsP 7J0574 7J-0574 38 Gallon Replacement Cartridge Kit for Caterpillar CAT Loader(7J0574)
HpaErtsP This is an aftermarket part manufactured to replace the 7J0574 7J-0574 and its OEM counterparts. || Durable construction: Built to withstand heavy use and harsh environments. || Precision Engineering: Designed to meet Caterpillar's exacting specifications for optimal performance. || Easy to install: Direct replacement for worn or damaged pump element (installation guide included). || Warranty: Backed by manufacturer's warranty for added peace of mind (warranty details included in package).
HpaErtsP This is an aftermarket part manufactured to replace the 7J0574 7J-0574 and its OEM counterparts. || Durable construction: Built to withstand heavy use and harsh environments. || Precision Engineering: Designed to meet Caterpillar's exacting specifications for optimal performance. || Easy to install: Direct replacement for worn or damaged pump element (installation guide included). || Warranty: Backed by manufacturer's warranty for added peace of mind (warranty details included in package).
$194.58
24 Feb 2020
-: -
CATERPILLAR / CAT 7J0574 7J-0574 CARTRIDGE KIT (CART KIT)
Number on catalog scheme:
None
For full view, you need register
Information:
Remove & Install Crankshaft Main Bearings
Start By:a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) which points to the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 6 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plates from each side of the No. 4 main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until Tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
Make sure the upper and lower halves of bearings are installed so bearing tabs (2) fit into the notch in cylinder block and bearing caps.
Do not put oil on parts until the bearing clearance has been checked.5. Use Tool (A) to install the upper bearings in the block. Make sure that the end of the bearing without the tab goes into the engine block first.6. Install the lower bearings in the bearing cap. When the bearing clearance is checked and the engine is in a vertical position, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.7. Check the bearing clearance with Plastigage (B) as follows:a. Put a piece of the Plastigage on the surface of the lower bearing half. b. Install the main bearing caps with arrow (6) toward the front of the cylinder block. Each cap has a number (7) on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put clean oil on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb ft).
Do not use an impact wrench to tighten the bolts the additional 120 degrees.
f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120 degrees. Tighten the bolts on the tab end of the cap 120 degrees.8. Remove the caps and measure the Plastigage. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to
Start By:a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) which points to the front of the block and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 6 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plates from each side of the No. 4 main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until Tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
Make sure the upper and lower halves of bearings are installed so bearing tabs (2) fit into the notch in cylinder block and bearing caps.
Do not put oil on parts until the bearing clearance has been checked.5. Use Tool (A) to install the upper bearings in the block. Make sure that the end of the bearing without the tab goes into the engine block first.6. Install the lower bearings in the bearing cap. When the bearing clearance is checked and the engine is in a vertical position, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. Do not turn the crankshaft when the Plastigage is in position to check clearances.7. Check the bearing clearance with Plastigage (B) as follows:a. Put a piece of the Plastigage on the surface of the lower bearing half. b. Install the main bearing caps with arrow (6) toward the front of the cylinder block. Each cap has a number (7) on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put clean oil on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb ft).
Do not use an impact wrench to tighten the bolts the additional 120 degrees.
f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120 degrees. Tighten the bolts on the tab end of the cap 120 degrees.8. Remove the caps and measure the Plastigage. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to
Caterpillar parts catalog:
Parts cartridge Caterpillar catalog:
623B, 623E
1693, 3406, 631C, 657B, 666, 769, 777, 824B, 826B, 983, 992, D348, D9G, D9H
183B, 621, 631C, 983, 992
621B, 824, 824B, 824S, 834, 977K, 977L, 980, 980B, 988
140, 141, 191, 824S, 992
631C, 633C, 772, 988, 992
623, 769, 950, 992
623B, 633D, 966C, 980
621B, 623B, 627B, 966C
631C, 633D, 824B
613, 613B
7J7057
CARTRIDGE ASSEM.
633, 633D
633, 633D
627B, 824B, 825B, 834, 980
623B, 633D, 966C, 980