2211166 CASE GP-TRANSMISSION Caterpillar parts
PF-300C, PS-300B
Rating:
Alternative (cross code) number:
CA2211166
221-1166
2211166
CA2211166
221-1166
2211166
PNEUMATIC COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$82.42
06 Jul 2021
91.4918[41.17] Pounds
LU: Amazon Global S
Gorecki 2211166 Wheel Cover Set Spyder 15 inch Pro White Caravan
Gorecki 15 inches, Gorecki || 4x, Gorecki || Durable, Gorecki
Gorecki 15 inches, Gorecki || 4x, Gorecki || Durable, Gorecki
Number on catalog scheme:
1
For full view, you need register
Information:
Procedure To Modify A Former 7U1722 or 7U7160 Hood Support Assembly To Provide Additional Strength
1. Fabricate plates (A) and (B) as shown in Illustrations 1 and 2. Use mild steel plate 8 mm (.3 in) thick.
Illustration 1. Dimensions required to fabricate plate (A).
Illustration 2. Dimensions required to fabricate plate (B).2. Trim 18 mm (.7 in) from the bottom edge of the former 7U1722 Support Assembly as shown in Illustration 3.
Illustration 3. Remove 18 mm (.7 in) from bottom edge of support assembly.
Illustration 4. Similar improvements can be performed to the exhaust piping arrangements.3. Repair any cracks by veeing out the crack and filling with weld material. Use AWS E7018 Electrode or equivalent.4. Lightly tack weld the fabricated plates in position as shown in Illustrations 5, 6, and 7. Do NOT finish weld until all associated parts will fit together correctly.
Illustration 5. Location of plates (A) and (B).
Illustration 6. Location detail for plate (A).
Illustration 7. Location detail for plate (B).5. Assemble the modified support. Check for correct fit and then finish weld. Provide pocket welds as shown in Illustration 6.6. Position the 2U2870 Fastener and center punch for the mounting bolts. Drill two 8.00 mm (.312 in) diameter holes as required and install the fastener.
Illustration 8. Partial view of engine hood group. (1) 2U2870 Fastener (typical). (2) 7U9187 Gas Strut.Procedure To Modify A Former 7U3338 Channel To Provide Additional Strength
1. Fabricate two plates (C) as shown in Illustration 9. Use 5 mm (.2 in) thick mild steel plate.
Illustration 9. Dimensions required to fabricate plate (C).2. Repair any cracks by veeing out the crack and filling with weld material. Use AWS E7018 Electrode or equivalent.3. Weld the fabricated plates to the channel as shown in Illustration 10. Position the plates by lining up the 14 by 22 mm (.55 by .87 in) slots with the slots in the existing channel.
Illustration 10. Weld plates (C) as shown. Use AWS E7018 Electrode or equivalent.
1. Fabricate plates (A) and (B) as shown in Illustrations 1 and 2. Use mild steel plate 8 mm (.3 in) thick.
Illustration 1. Dimensions required to fabricate plate (A).
Illustration 2. Dimensions required to fabricate plate (B).2. Trim 18 mm (.7 in) from the bottom edge of the former 7U1722 Support Assembly as shown in Illustration 3.
Illustration 3. Remove 18 mm (.7 in) from bottom edge of support assembly.
Illustration 4. Similar improvements can be performed to the exhaust piping arrangements.3. Repair any cracks by veeing out the crack and filling with weld material. Use AWS E7018 Electrode or equivalent.4. Lightly tack weld the fabricated plates in position as shown in Illustrations 5, 6, and 7. Do NOT finish weld until all associated parts will fit together correctly.
Illustration 5. Location of plates (A) and (B).
Illustration 6. Location detail for plate (A).
Illustration 7. Location detail for plate (B).5. Assemble the modified support. Check for correct fit and then finish weld. Provide pocket welds as shown in Illustration 6.6. Position the 2U2870 Fastener and center punch for the mounting bolts. Drill two 8.00 mm (.312 in) diameter holes as required and install the fastener.
Illustration 8. Partial view of engine hood group. (1) 2U2870 Fastener (typical). (2) 7U9187 Gas Strut.Procedure To Modify A Former 7U3338 Channel To Provide Additional Strength
1. Fabricate two plates (C) as shown in Illustration 9. Use 5 mm (.2 in) thick mild steel plate.
Illustration 9. Dimensions required to fabricate plate (C).2. Repair any cracks by veeing out the crack and filling with weld material. Use AWS E7018 Electrode or equivalent.3. Weld the fabricated plates to the channel as shown in Illustration 10. Position the plates by lining up the 14 by 22 mm (.55 by .87 in) slots with the slots in the existing channel.
Illustration 10. Weld plates (C) as shown. Use AWS E7018 Electrode or equivalent.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts case Caterpillar catalog:
1258748
CASE GP-CHAIN DRIVE
RM-250C, RR-250B
RM-250C, RR-250B
1059045
CASE & COVERS GP-DIFFERENTIAL
RR-250, SS-250
RR-250, SS-250
7R3832
CASE AS-CHAIN-RH
RR-250, SS-250
RR-250, SS-250
2283267
CASE GP-CHAIN DRIVE
RM-500
RM-500
1871423
CASE GP-CHAIN DRIVE
RM-350B
RM-350B