3617768 CASE AS-DIFFERENTIAL Caterpillar parts
966M, 966M XE, 972M, 972M XE
Rating:
Alternative (cross code) number:
CA3617768
361-7768
3617768
CA3617768
361-7768
3617768
Weight: 102 pounds 46 kg.
WHEEL LOADER,
Number on catalog scheme:
5
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Remove the balancer shaft. Refer toDisassembly and Assembly, "Balancer Shaft - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing Remove" .
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00602186
Use Tool (A) to remove the six balancer shaft bearing. Pull the balancer shaft bearings toward the flywheel end of the engine.Installation Procedure
Illustration 2 g00602186
Illustration 3 g00602205
(A) The front bearing depth is 0.8 0.5 mm (0.03 0.02 inch). (B) The center bearing depth is 290.6 0.5 mm (11.44 0.02 inch). (C) The rear bearing depth is 601.0 0.5 mm (23.66 0.02 inch).
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Install the balancer shaft front bearing with Tool (A). Ensure that the holes in the bearings are aligned with the holes in the cylinder block. The bearing must be 0.8 0.5 mm (0.03 0.02 inch) inside the front face of the cylinder block after installation.
Install the balancer shaft center bearing with Tool (A). Ensure that the holes in the bearings are aligned with the holes in the cylinder block. The bearing must be 290.6 0.5 mm (11.44 0.02 inch) inside the front face of the cylinder block after installation.
Install the balancer shaft rear bearing with Tool (A). Ensure that the holes in the bearings are aligned with the holes in the cylinder block. The bearing must be 601.0 0.5 mm (23.66 0.02 inch) inside the front face of the cylinder block after installation.
Check the bore of the bearings. The balancer shaft bearing bore must be 53.05 0.06 mm (2.089 0.002 inch) after installation.End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install" .
Install the balancer shaft. Refer to Disassembly and Assembly, "Balancer Shaft - Remove
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Remove the balancer shaft. Refer toDisassembly and Assembly, "Balancer Shaft - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing Remove" .
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00602186
Use Tool (A) to remove the six balancer shaft bearing. Pull the balancer shaft bearings toward the flywheel end of the engine.Installation Procedure
Illustration 2 g00602186
Illustration 3 g00602205
(A) The front bearing depth is 0.8 0.5 mm (0.03 0.02 inch). (B) The center bearing depth is 290.6 0.5 mm (11.44 0.02 inch). (C) The rear bearing depth is 601.0 0.5 mm (23.66 0.02 inch).
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Install the balancer shaft front bearing with Tool (A). Ensure that the holes in the bearings are aligned with the holes in the cylinder block. The bearing must be 0.8 0.5 mm (0.03 0.02 inch) inside the front face of the cylinder block after installation.
Install the balancer shaft center bearing with Tool (A). Ensure that the holes in the bearings are aligned with the holes in the cylinder block. The bearing must be 290.6 0.5 mm (11.44 0.02 inch) inside the front face of the cylinder block after installation.
Install the balancer shaft rear bearing with Tool (A). Ensure that the holes in the bearings are aligned with the holes in the cylinder block. The bearing must be 601.0 0.5 mm (23.66 0.02 inch) inside the front face of the cylinder block after installation.
Check the bore of the bearings. The balancer shaft bearing bore must be 53.05 0.06 mm (2.089 0.002 inch) after installation.End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install" .
Install the balancer shaft. Refer to Disassembly and Assembly, "Balancer Shaft - Remove
Caterpillar parts catalog:
Parts case Caterpillar catalog:
3453374
CASE AS-TRANSFER GEAR
966K, 966M XE, 972M XE
966K, 966M XE, 972M XE
3453373
CASE GP-TRANSMISSION
966K, 966M XE, 972M XE
966K, 966M XE, 972M XE
3649710
CASE GP-TRANSMISSION
966M XE, 972M XE
966M XE, 972M XE
4448360
CASE GP-TRANSMISSION
966M XE, 972M XE
966M XE, 972M XE
2919129
CASE
824K, 825K, 826K, 834K, 836K, 950K, 962K, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M, 988K
824K, 825K, 826K, 834K, 836K, 950K, 962K, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M, 988K
824K, 825K, 826K, 834K, 836K, 950K, 962K, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M, 988K
3617764
CASE AS-DIFFERENTIAL
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE
3653045
CASE AS-TRANSFER
24M, 834K, 836K, 988K
24M, 834K, 836K, 988K
4196886
CASE AS
834K, 836K, 988K
834K, 836K, 988K
4222820
CASE AS-TRANSMISSION
824K, 825K, 826K, 834K, 836K, 980M, 982M, 988K
824K, 825K, 826K, 834K, 836K, 980M, 982M, 988K
3763744
CASE AS-DIFFERENTIAL
982M, 986H
982M, 986H
4174072
CASE
950 GC
950 GC
3860310
CASE AS
980M
980M
3763756
CASE-DIFFERENTIAL
980M, 982M
980M, 982M
3617764
CASE AS-DIFFERENTIAL
966M, 966M XE, 972M, 972M XE
966M, 966M XE, 972M, 972M XE