6G1601 CHAIN GP Caterpillar parts
16G, 16H, 16H NA, 16M
Rating:
Alternative (cross code) number:
CA6G1601
6G-1601
6G1601
CA6G1601
6G-1601
6G1601
Weight: 115 pounds 52 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$404.35
24 Oct 2023
CN: Xinghongyu
Wire Connector Pin-212 213 214 215 218 SPL-2 3 Universal Terminal 0.08-2.5Mm Push-In Electrical Terminals For Cable Connection LT-422 10 PCS
Zuchec Material Of Insulation:Modified Nylon(PA66) || Origin:CN(Origin) || Certification:CE || Certification:NONE || Rated Voltage:250V
Zuchec Material Of Insulation:Modified Nylon(PA66) || Origin:CN(Origin) || Certification:CE || Certification:NONE || Rated Voltage:250V
This part in 2 request:
Show.
This information for suppliers only!
2021-08-18
2020-02-22
Number on catalog scheme:
1
For full view, you need register
Information:
Complete the procedure in the order in which the steps are listed.
Table 4
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the 12-pin connector for the PETU and the C2 DCU connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
B. Thoroughly inspect the connector for the suspect solenoid valve. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires in the 12-pin connector for the PETU, the C2 DCU connector, and the solenoid connectors that are associated with the active diagnostic code.
D. Check the harness for corrosion, abrasion, and pinch points from the solenoids to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 20 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: A 3363-5 or 3126-5 diagnostic code is active.
Proceed to Test Step 3.
Result: A 3363-6 or 3126-6 diagnostic code is active.
Proceed to Test Step 4.
Result: A 3361-5, 3821-5 , 3361-6 or 3821-6 diagnostic code is active.
Proceed to Test Step 5.
3. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, free of corrosion and securely connected.
B. Disconnect the solenoid from the applicable harness.
C. Connect a jumper wire between the terminals of the harness connector for the suspect coil. The coil is replaced with a short circuit.
D. Perform the appropriate electrical checkout.
Table 4
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the 12-pin connector for the PETU and the C2 DCU connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
B. Thoroughly inspect the connector for the suspect solenoid valve. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires in the 12-pin connector for the PETU, the C2 DCU connector, and the solenoid connectors that are associated with the active diagnostic code.
D. Check the harness for corrosion, abrasion, and pinch points from the solenoids to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 20 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: A 3363-5 or 3126-5 diagnostic code is active.
Proceed to Test Step 3.
Result: A 3363-6 or 3126-6 diagnostic code is active.
Proceed to Test Step 4.
Result: A 3361-5, 3821-5 , 3361-6 or 3821-6 diagnostic code is active.
Proceed to Test Step 5.
3. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, free of corrosion and securely connected.
B. Disconnect the solenoid from the applicable harness.
C. Connect a jumper wire between the terminals of the harness connector for the suspect coil. The coil is replaced with a short circuit.
D. Perform the appropriate electrical checkout.
Caterpillar parts catalog:
Parts chain Caterpillar catalog:
6G1740
CHAIN GP
16G, 16H, 16H NA, 16M
16G, 16H, 16H NA, 16M
120G, 12E, 12G, 130G, 140G, 14G, 16, 16G, 561B, 583H, 613C, 621, 621E, 623E, 627E, 631E, 637E, 651, 651E, 657E, 666, 784B, 824, 980, 988, D315, D320A, D337, D342, D342C, D343, D353C, D379, D398, D4D, ...
8D2799
CHAIN ASSEM.
12F, 12G, 14E, 14G, 16G
12F, 12G, 14E, 14G, 16G
8D1646
CHAIN
16G
16G
14G, 14H, 14H NA, 14M
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G
120G, 120H, 120H ES, 120H NA, 120K
4S6239
CHAIN
D9G
D9G
3389709
CHAIN
824K, 825K, 826K, 836H, 836K
824K, 825K, 826K, 836H, 836K
1615839
CHAIN AS
A13
A13
3Q8848
CHAIN
120H, 12H, 12H NA, 140H, 140H NA
120H, 12H, 12H NA, 140H, 140H NA
7Z3810
CHAIN
120H, 12H, 12H NA, 140H, 140H NA
120H, 12H, 12H NA, 140H, 140H NA
7Z3811
CHAIN
12H, 12H NA, 140H, 140H NA
12H, 12H NA, 140H, 140H NA
2669720
CHAIN
24H, 24M
24H, 24M
160H, 160H ES, 160H NA, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 163H NA