4N3714 CHAMBER AS Caterpillar parts
245, 3406, 3408, 3412, 637D, 992C
Rating:
Alternative (cross code) number:
CA4N3714
4N-3714
4N3714
CA4N3714
4N-3714
4N3714
Weight: 2 pounds 1 kg.
EXCAVATOR, WHEEL TRACTOR,
Related part:
4N3714
CHAMBER-PC-YM
3637450
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4N3714 PRE-COMBUSTION CHAMBER Suitable For Caterpillar® 4N3714
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
CTP 4N3714 Combustion Chamber for Engine Model 3406, 3408, 3412
CTP For Engine Model 3406, 3408, 3412 || Highly Efficient || Easy in-and-out fit
CTP For Engine Model 3406, 3408, 3412 || Highly Efficient || Easy in-and-out fit
This part in 2 request:
Show.
This information for suppliers only!
2019-09-24
2016-09-02
Compatible equipment models: 4N3714:
Information:
If a diagnostic code is generated for the engine speed/timing sensor, refer to the Troubleshooting manual.For proper operation, the condition and installation of the sensor must be correct. If the condition or the installation of the sensor is suspect, use the following procedure.
Illustration 1 g00760464
(1) Engine speed/timing sensor
Remove engine speed/timing sensor (1). Inspect the condition of the end of the magnet. Look for wear and contaminants.
Clean any debris from the face of the magnet.
Illustration 2 g00909543
(2) Sliphead
Check the tension of sliphead (2). Gently extend the sliphead for a minimum of 4 mm (0.16 inch). Then push back the sliphead. When the sliphead has the correct tension, at least 22 N (5 lb) of force is required to push in the sliphead from the extended position.
The sliphead must be fully extended when the speed/timing sensor is installed so that the sensor maintains the correct clearance with the speed-timing wheel. If the correct clearance is not maintained, the signal from the sensor will not be generated.Do not install the sensor between the teeth of the speed-timing wheel. Damage to the sensor would result. Before installing the sensor, ensure that a tooth of the wheel is visible in the mounting hole for the sensor.
Install the engine speed/timing sensor.
Ensure that a tooth on the speed-timing wheel is visible in the mounting hole for the sensor.
Extend sliphead (2) by a minimum of 4 mm (0.16 inch).
Coat the threads of the sensor with 4C-5598 High Temperature Anti-Seize. Note: The sliphead is designed to contact a tooth of the speed-timing wheel. The maximum allowable gap between the sliphead and the tooth is 0.5 mm (0.02 inch).
Install the sensor. Tighten the locknut to 40 5 N m (30 4 lb ft). Timing Calibration
Calibration of the timing is required only after the following circumstances:
The master Electronic Control Module (ECM) has been replaced.
The speed/timing sensor has been replaced.
The speed-timing wheel and/or the rear gear train have been adjusted.
The speed-timing wheel and/or the rear gear train have been replaced.The Caterpillar Electronic Technician (ET) uses the engine speed/timing sensor to help calibrate the engine timing. For instructions on the timing calibration, refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
Illustration 1 g00760464
(1) Engine speed/timing sensor
Remove engine speed/timing sensor (1). Inspect the condition of the end of the magnet. Look for wear and contaminants.
Clean any debris from the face of the magnet.
Illustration 2 g00909543
(2) Sliphead
Check the tension of sliphead (2). Gently extend the sliphead for a minimum of 4 mm (0.16 inch). Then push back the sliphead. When the sliphead has the correct tension, at least 22 N (5 lb) of force is required to push in the sliphead from the extended position.
The sliphead must be fully extended when the speed/timing sensor is installed so that the sensor maintains the correct clearance with the speed-timing wheel. If the correct clearance is not maintained, the signal from the sensor will not be generated.Do not install the sensor between the teeth of the speed-timing wheel. Damage to the sensor would result. Before installing the sensor, ensure that a tooth of the wheel is visible in the mounting hole for the sensor.
Install the engine speed/timing sensor.
Ensure that a tooth on the speed-timing wheel is visible in the mounting hole for the sensor.
Extend sliphead (2) by a minimum of 4 mm (0.16 inch).
Coat the threads of the sensor with 4C-5598 High Temperature Anti-Seize. Note: The sliphead is designed to contact a tooth of the speed-timing wheel. The maximum allowable gap between the sliphead and the tooth is 0.5 mm (0.02 inch).
Install the sensor. Tighten the locknut to 40 5 N m (30 4 lb ft). Timing Calibration
Calibration of the timing is required only after the following circumstances:
The master Electronic Control Module (ECM) has been replaced.
The speed/timing sensor has been replaced.
The speed-timing wheel and/or the rear gear train have been adjusted.
The speed-timing wheel and/or the rear gear train have been replaced.The Caterpillar Electronic Technician (ET) uses the engine speed/timing sensor to help calibrate the engine timing. For instructions on the timing calibration, refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
Cat SIS web machinery list:
Parts chamber Caterpillar catalog:
1H9570
CHAMBER
3406B, 3408, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C32, D342, D348, D353C, D364, D379A, D398A, G3508, G3508B, G3512, G3512B, G3516, G3516B, G352...
3406B, 3408, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C32, D342, D348, D353C, D364, D379A, D398A, G3508, G3508B, G3512, G3512B, G3516, G3516B, G352...
9N6276
CHAMBER AS
3408
3408
1486528
CHAMBER GP-MIXING
RM-350B
RM-350B
3787433
CHAMBER GP-ROTOR
PM-201
PM-201
3322732
CHAMBER GP-ROTOR
PM-201
PM-201
2643903
CHAMBER GP-ROTOR
PM-201
PM-201
1314766
CHAMBER GP-ROTOR
PM-465
PM-465
8S3990
CHAMBER ASSEM.
3304, 3306, D5B
3304, 3306, D5B
5L6039
CHAMBER ASSEM.
D353C, D379A, D398A, D399
D353C, D379A, D398A, D399
5S9609
CHAMBER ASSEM.
1674, D334
1674, D334
5S6795
CHAMBER ASSEMBLY PRECOMBUSTION
120B, 12G, 3304, 3306, 561C, 920, 930, 941, 951B, D4D, D4E, D5, D5B, D6C
120B, 12G, 3304, 3306, 561C, 920, 930, 941, 951B, D4D, D4E, D5, D5B, D6C
1H9570
CHAMBER
3406B, 3408, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C32, D342, D348, D353C, D364, D379A, D398A, G3508, G3508B, G3512, G3512B, G3516, G3516B, G352...
3406B, 3408, 3408C, 3412, 3412C, 3412D, 3412E, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C32, D342, D348, D353C, D364, D379A, D398A, G3508, G3508B, G3512, G3512B, G3516, G3516B, G352...