3C8311 CHASSIS OPT Caterpillar parts
Rating:
Alternative (cross code) number:
CA3C8311
3C-8311
3C8311
CA3C8311
3C-8311
3C8311
Weight: 0.12 pounds 0 kg.
For full view, you need register
Information:
Removal Procedure
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01183923
Drain the level of the coolant below the coolant temperature sensor into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Disconnect the harness assembly from coolant temperature sensor (1) .
Remove coolant temperature sensor (1) .
Inspect the condition of the O-ring seal on coolant temperature sensor (1). Replace the O-ring seal, if necessary.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01183923
Install coolant temperature sensor (1). Tighten coolant temperature sensor (1) to a torque of 20 5 N m (15 4 lb ft).
Connect the harness assembly to coolant temperature sensor (1) .
Refill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove cooling system pressure cap slowly to relieve pressure only when engine is stopped and cooling system pressure cap is cool enough to touch with your bare hand.Do not attempt to tighten hose connections when the coolant is hot, the hose can come off causing burns.Cooling System Coolant Additive contains alkali. Avoid contact with skin and eyes.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01183923
Drain the level of the coolant below the coolant temperature sensor into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Disconnect the harness assembly from coolant temperature sensor (1) .
Remove coolant temperature sensor (1) .
Inspect the condition of the O-ring seal on coolant temperature sensor (1). Replace the O-ring seal, if necessary.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01183923
Install coolant temperature sensor (1). Tighten coolant temperature sensor (1) to a torque of 20 5 N m (15 4 lb ft).
Connect the harness assembly to coolant temperature sensor (1) .
Refill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change".