1361419 CLAMP Caterpillar parts
312B L, 312C, 312D, 315B L, 554, 906H, 906H2, 907H, 907H2, 908H, 908H2, 910K, 914K, PF-300C, PS-300B, TH103, TH62, TH63, TH82, TH83
Rating:
Alternative (cross code) number:
CA1361419
136-1419
1361419
CA1361419
136-1419
1361419
Weight: 0.56 pounds 0 kg.
COMPACT WHEEL LOADER, TELEHANDLER,
Compatible equipment models: 1361419:
Number on catalog scheme:
11
For full view, you need register
Information:
Which Generate This Code:This diagnostic code is recorded when the Power Train ECM identifies a system voltage that is below 21.3 DCV.This diagnostic code is caused by the following:
The system voltage remains low for an extended time after the engine is started.
There is a connection with high impedance between the battery and the ECM.
There is a connection with high impedance between the ECM and system ground.
One of the batteries is disconnected with the key in the ON position. Also, the engine must not be running.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0168 FMI 01 is active before performing this procedure.Test Step 1. CHECK THE BATTERY VOLTAGE
Start the engine.
Operate the engine at high idle for several minutes.Expected Result:Battery voltage is greater than 21.3 DCV.Results:
YES - Battery voltage is greater than 21.3 DCV. The battery voltage is correct. Proceed to Test Step 2.
NO - Battery voltage is below 21.3 DCV.Repair: The charging system is not operating correctly. Check the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".STOPTest Step 2. CHECK THE SYSTEM VOLTAGE AT THE POWER TRAIN ECM
The engine must be running at high idle.
Measure the system voltage between contact J1-1 (wire 164-WH) and contacts J1-13, J1-23, J1-57 and J1-70 (wire 202-BK). Measure the system voltage at the contacts of the harness connector.Expected Result:The voltage is below 21.3 DCV.Results:
YES - Voltage is below 21.3 DCV.Repair: Repair the machine harness or replace the machine harness.STOP
NO - Voltage is greater than 21.3 DCV.Repair: The system voltage is correct. Ensure that service code CID 0168 FMI 01 is still active. Disconnect the Power Train ECM. Inspect the following contacts:
J1-1
J1-13
J1-23
J1-57
J1-70 (wire 202-BK)Connect the harness connector to the Power Train ECM. If the diagnostic code is active, replace the Power Train ECM. Refer to Troubleshooting, Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
The system voltage remains low for an extended time after the engine is started.
There is a connection with high impedance between the battery and the ECM.
There is a connection with high impedance between the ECM and system ground.
One of the batteries is disconnected with the key in the ON position. Also, the engine must not be running.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0168 FMI 01 is active before performing this procedure.Test Step 1. CHECK THE BATTERY VOLTAGE
Start the engine.
Operate the engine at high idle for several minutes.Expected Result:Battery voltage is greater than 21.3 DCV.Results:
YES - Battery voltage is greater than 21.3 DCV. The battery voltage is correct. Proceed to Test Step 2.
NO - Battery voltage is below 21.3 DCV.Repair: The charging system is not operating correctly. Check the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".STOPTest Step 2. CHECK THE SYSTEM VOLTAGE AT THE POWER TRAIN ECM
The engine must be running at high idle.
Measure the system voltage between contact J1-1 (wire 164-WH) and contacts J1-13, J1-23, J1-57 and J1-70 (wire 202-BK). Measure the system voltage at the contacts of the harness connector.Expected Result:The voltage is below 21.3 DCV.Results:
YES - Voltage is below 21.3 DCV.Repair: Repair the machine harness or replace the machine harness.STOP
NO - Voltage is greater than 21.3 DCV.Repair: The system voltage is correct. Ensure that service code CID 0168 FMI 01 is still active. Disconnect the Power Train ECM. Inspect the following contacts:
J1-1
J1-13
J1-23
J1-57
J1-70 (wire 202-BK)Connect the harness connector to the Power Train ECM. If the diagnostic code is active, replace the Power Train ECM. Refer to Troubleshooting, Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Cat SIS web machinery list:
Parts clamp Caterpillar catalog:
120H, 120H NA, 135H, 135H NA, 2384C, 2484C, 30/30, 3126B, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR,...
216, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 248, 24H, 24M, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B, 268B, 272C, 277C, 277C2, 277D, 279C, 279...
120H, 120M, 120M 2, 12H, 12M, 135H, 140H, 140K, 140M, 143H, 14H, 14M, 160H, 160K, 160M, 163H, 24H, 2864C, 3126, 3176B, 3176C, 3196, 320B, 325B L, 330B L, 330C, 330C L, 3406E, 3408, 3408B, 3408C, 3412,...
120M, 12M, 140M, 14M, 160M, 16M, 3054C, 312B L, 312C, 315B L, 320B, 322B L, 322B LN, 325B L, 325C FM, 325D FM LL, 330B L, 330C FM, 330D FM, 3456, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 385B...
120G, 12G, 130G, 140G, 14G, 14M, 16G, 216, 216B, 216B3, 226B, 226B3, 228, 236, 236B, 242B, 247, 247B, 247B3, 248, 252B, 259B3, 267, 267B, 268B, 2864C, 287, 3406B, 3406C, 414E, 416, 416B, 416D, 416E, 4...
120H, 120H ES, 120H NA, 120M, 12M, 135H, 135H NA, 3114, 3116, 3126, 320 L, 3208, 322B L, 322B LN, 322C, 322C FM, 325, 325 LN, 325B, 325B L, 414E, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, ...
231D, 235C, 235D, 2384C, 2484C, 24H, 2864C, 30/30, 311C, 311D LRR, 311F LRR, 3126B, 312C, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 316E L, 3176B, 3176C, 31...
120K, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L,...
120G, 130G, 14G, 225, 225D, 227, 231D, 235, 3304, 518, 528, 561B, 572G, 583K, 594H, 613B, 627B, 815, 920, 941, 950, 951B, 955H, 955K, 955L, 966C, 977K, 977L, 980B, 983B, D4D, D5, D6C, D6D, D6E, D6E SR...
216, 228, 236, 247, 248, 267, 287, 3054C, 3054E, 3056E, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, ...
12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 236D, 242D, 246D, 257D, 259D, 262D, 277D, 279D, 287D, 289D, 308E2 CR, 3512C, 3516C, 725, 725C, 730, 730C, 7...
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315, 315B, 315C, 318B, 320 L, 320B, 320B L
120M, 12M, 140M, 14M, 160M, 16M, 3054C, 312B L, 312C, 315B L, 320B, 322B L, 322B LN, 325B L, 325C FM, 325D FM LL, 330B L, 330C FM, 330D FM, 3456, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 385B...
1464094
CLAMP-HOSE
312B L, CB-534C, PS-300B, TH103, TH62, TH63, TH82, TH83
312B L, CB-534C, PS-300B, TH103, TH62, TH63, TH82, TH83
3054, 3054B, 3056, 312B L, 315B L, 416C, 416D, 420D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D, 554, 908, 924G, 924GZ, AP-800C, BG-225B, BG-225C, CB-434C, CB-534C, CB-535B, CP-433C, CP-433E, CS-3...
1016789
CLAMP-HOSE
3054, 3056, 307, 914G, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, PS-300B, TH62, TH63, TH82
3054, 3056, 307, 914G, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, IT14G, PS-300B, TH62, TH63, TH82
0838449
CLAMP GP-PIPE
RT100, TH62, TH63, TH82, TH83
RT100, TH62, TH63, TH82, TH83
3054, 3054B, 3056, 315B L, 554, AP-800C, BG-225B, BG-225C, CB-434C, CB-534C, CB-535B, CP-433C, CS-323C, CS-431C, CS-433C, M312, M315, PS-150B, PS-300B, TH103, TH62, TH63, TH82, TH83
30/30, 416F, 420F, 422F, 428F, 430F, 432F, 434F, 444F, 508, 906H, 906H2, 907H, 907H2, 908H, 908H2, AP-1000B, AP-1055B, AP-800, AP-800D, AP-900B, AS2252C, BG-2455C, BG-245C, CB-334E, CB-335D, CS-531C, ...
1011878
CLAMP
RT50, TH103, TH62, TH63, TH82, TH83
RT50, TH103, TH62, TH63, TH82, TH83
3U5422
CLAMP
D250B, D250D, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B, TH103, TH62, TH63, TH82, TH83
D250B, D250D, D250E, D250E II, D25C, D25D, D300B, D300D, D300E, D300E II, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D, D44B, D550B, TH103, TH62, TH63, TH82, TH83
TH103, TH62, TH63, TH82, TH83
TH103, TH210, TH215, TH62, TH63, TH82, TH83
3054, 3054C, 3054E, 3056, 312, 312B L, 914G, C4.4, C6.6, IT14G, M312, M315, PS-200B, TH103, TH62, TH63, TH82, TH83