8C4586 CLAMP Caterpillar parts
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H, 3...
Rating:
Alternative (cross code) number:
CA8C4586
8C-4586
8C4586
CA8C4586
8C-4586
8C4586
Weight: 0.08 pounds 0 kg.
ARTICULATED TRUCK, WHEEL TRACTOR,
Compatible equipment models: 8C4586:
FRONT SHOVEL
5080
MINI HYD EXCAVATOR
307B
MOTOR GRADER
120H
120H ES
120H NA
120K
120K 2
12H
12H ES
12H NA
12K
135H
135H NA
140H
140H ES
140H NA
140K
140K 2
143H
14H
14H NA
160H
160H ES
160H NA
160K
163H
163H NA
16H
16H NA
24H
PIPELAYER
572R
TRACK-TYPE TRACTOR
30/30
D10R
D11R
D3C III
D4C III
D4H
D4H XL
D5C III
D5H
D5H XL
D5M
D5N
D6H
D6H XL
D6M
D6N
D6R
D9R
DEUCE
TRACTOR
776D
VIBRATORY COMPACTOR
CP-433E
CP-44
CP-533E
CP-56
CP-573E
CP-64
CP-663E
CP-76
CS-423E
CS-433E
CS-44
CS-531D
CS-533D
CS-533E
CS-54
CS-56
CS-563D
CS-563E
CS-573D
CS-583D
CS-583E
CS-64
CS-663E
CS-683E
CS-74
Number on catalog scheme:
11
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 g01149952
Position new upper main bearing (4) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Install the thrust plates on each side of the No. 4 main bearing. Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 2 g01149987
Position main bearing caps (2) on the crankshaft. Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (1) and bolts (3) with clean engine oil. Install the bolts.
Tighten bolts (1) and bolts (3) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft). Note: Bolt (A) is on the bearing tab side of the main
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator 1
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the cylinder block. The upper halves of the main bearings have the oil groove and the oil hole.
Illustration 1 g01149952
Position new upper main bearing (4) on the crankshaft. Insert the end of the upper main bearing that does not have the tab into the cylinder block. Install Tooling (A) in the oil hole of the crankshaft. Carefully rotate the crankshaft in order to push the upper main bearing into the cylinder block. Note: Push the upper main bearing from the side of the bearing tab with Tooling (A). If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft.
Install the thrust plates on each side of the No. 4 main bearing. Note: Install the thrust plates with the words "Block Side" toward the cylinder block.
Install the lower halves of the crankshaft main bearings in the main bearing caps. Note: Ensure that the main bearings are installed so that bearing tabs fit into the notch in the main bearing caps.
Illustration 2 g01149987
Position main bearing caps (2) on the crankshaft. Note: Ensure that the numbers on the main bearing caps match the numbers on the cylinder block. Also ensure that the "FRONT" on the main bearing cap is installed toward the front of the cylinder block.
Lubricate the threads of bolts (1) and bolts (3) with clean engine oil. Install the bolts.
Tighten bolts (1) and bolts (3) for the main bearing caps, as follows:
Tighten Bolt (A) to a torque of 258 14 N m (190 10 lb ft). Note: Bolt (A) is on the bearing tab side of the main
Cat SIS web machinery list:
Parts clamp Caterpillar catalog:
515, 517, 518, 518C, 525, 525B, 525C, 527, 528, 528B, 530B, 535B, 535C, 545C, D3
140H, 143H, 14H, 160H, 163H, 16H, 16H NA, 844, 938G II, 950G II, 962G II, 990, 990 II, 992C, 992D, IT38G II
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 621G, ...
24H, 631D, 637D, 639D, 69D, 768C, 769C, 988B, 988F, AD40, AD45, AE40, AE40 II, CB-434D, CB-521, CD-54
657, 69D, 972G, 972G II, AD45B, AD55, D8H
350, 350 L, 365B, 365B II, 365C, 375, 375 L, 385B, 385C, 385C FS, 385C L, 5080, 5090B, 5110B, 988G, 988H, 988K, 992G, 992K, 993K
950G II, 950H, 988F, 988F II
1090, 1190, 1190T, 120M, 1290T, 1390, 140M, 14M, 160M, 2384C, 2484C, 2590, 521B, 522B, 525C, 535C, 541, 541 2, 545C, 551, 552, 552 2, 559C, 579C, 793D, 815B, 834H, 836H, 988H, R1300G II, TK741, TK751,...
140H, 143H, 14H, 14M, 160H, 163H, 16H, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 950H, D7E
776C, 776D, 777B, 777D, 777F, 777G
525B, 535B, 797B, D10N, D10R, D10T, D11R, D11T
320 L, 322B L, 322B LN, 322C, 322C FM, 324D FM, 324D FM LL, 324D L, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325D FM, 325D FM LL, 325D L, 325D MH, 329D L, 330, 330 L, 350, E240C, EL240B, M325B
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 1390, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 16...
1060419
CLAMP
416B, 426B, 428B, 436B, 438B, 446B
416B, 426B, 428B, 436B, 438B, 446B
12F, 183B, 225, 3003, 3013, 3013C, 3014, 3024, 3024C, 3054, 3054C, 3054E, 307, 308C, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 322 FM L, 330, 330 L, 3304, 3306, 35, 350, 375, 375 L, 416, 416B, 416...
5G8108
CLAMP
416B, 416C, 416D, 420D, 424B, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 914G, IT12B, IT14B, IT14G
416B, 416C, 416D, 420D, 424B, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 914G, IT12B, IT14B, IT14G
3054, 3054B, 3056, 3114, 3116, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314E CR, 314E LCR, 316E L, 318D2 L, 318E L, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L, 349E, 3...
120B, 120G, 12G, 130G, 140B, 140G, 1673C, 215, 225, 235, 330, 3304, 3306, 330B L, 350, 3512, 416, 416B, 428, 428B, 528, 594H, 627B, 637D, 815B, 920, 930, 930R, 941, 950, 950B, 955L, 963, 966C, 966D, 9...
9R6266
CLAMP AS
446, 446B, 446D
446, 446B, 446D
4P2767
CLAMP AS
3114, 446, 446B, 446D, 924F, CB-434, IT18F, IT24F
3114, 446, 446B, 446D, 924F, CB-434, IT18F, IT24F
3114, 312, 315, 315B L, 317, 446, 446B, 446D, 914G, 916, 926, 943, IT12B, IT14G, IT28
120B, 12F, 215, 312, 312B L, 312C, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315, 315B L, 315C, 317, 318D2 L, 3208, 446, 446B, 446D, 561C, 916, 920, 926, 926A, 930, 930R, 941, 943, 953, AP-650B, AP-...
120H, 120H NA, 12H, 12H ES, 12H NA, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 235C, 235D, 245B, 245D, 30/30, 3114, 3116, 312C, 312C L, 315C, 3176B, 3176C,...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...