AVSPARE.COM
parts catalog

CLIP 0004664 - Caterpillar



0004664 CLIP Caterpillar parts CLIP
Rating:
46
Alternative (cross code) number:
CA0004664
000-4664
0004664
Caterpillar 0004664 CLIP

Buy CLIP 0004664 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Piston Pump
Illustration 1 g00891299
(1) Actuator piston (2) Feedback lever (3) Solenoid (4) Passage (5) Servo valve (6) Pressure override valve (POR Valve) (7) Port for the drive loop (8) Input shaft (9) Swashplate (10) Piston (11) Barrel (12) Spring (13) Port Plate (14) Port for drive loop (15) Charge pumpThe tandem pumps for the hydrostatic drive system are variable displacement piston pumps. The tandem pumps are mounted to the rear of the engine. The input shaft of the front pump engages a coupling that is mounted to the flywheel of the engine in order to drive the tandem pumps. When the engine is running, shaft (8) and barrel (11) are rotating. There are nine pistons (10) in barrel (11). Port plate (13) and swashplate (9) are stationary within the pump housing. Port plate (13) and swashplate (9) do not rotate. Spring (12) maintains a force against barrel (11) and port plate (13). When barrel (11) is rotating, each piston (10) follows the angle of swashplate (9) .If the angle of swashplate (9) is zero, pistons (10) do not move in and out of barrel (11) and there is no oil flow. Charge oil from charge pump (15) maintains oil pressure in the pump in order to perform the following tasks:
Keep barrel (11) full of oil.
Lubricate the pump components.
Provide makeup oil for internal loss of oil that is due to leakage.
Provide pilot oil to servo valve (5) in order to shift actuator piston (1) and change the angle of swashplate (9) .
The charge pump of the rear piston pump provides pilot oil in order to release the parking brakes.For additional information, refer to "Charge Pump".The position of swashplate (9) is determined by actuator piston (1). The speed and direction control that is located on the left console sends signals to the electronic control module (ECM). The ECM interprets the signals and the ECM sends pulse width modulated signals to solenoids (3) on either side of servo valve (5). As servo valve (5) is shifted to either direction, signal oil from passage (4) is directed to the corresponding end of actuator piston (1) .As actuator piston (1) begins to move, the angle of swashplate (9) begins to increase. As piston (10) follows swashplate (9), pistons (10) begin to move in and out of barrel (11). As piston (10) moves out of barrel (11), oil is drawn from the passage of port (7) of the drive loop through port plate (13). As piston (10) follows swashplate (9) and the piston moves into barrel (11), the oil is pushed through port plate (13) into the passage to port (14) of the drive loop.As the angle of swashplate (9) increases, the output flow of the pump also increases.Charge Pump
Illustration 2 g01013499
Charge pump (1) Pressure override valve (POR Valve) (2) Passage (3) Crossover relief valve (4) Passage (5) Orifice (6) Passage (7) Supply passage for the charge pump (8) Passage (9) Resolver (10) Charge relief valve (11) Crossover relief valve (12) Oil filter (13) Passage (14)


Parts clip Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.