CLUTCH GP-TRANSMISSION 6Y2301 - Caterpillar

Illustration 6 g06123870
Cab upper left-hand switch panel
(J) aux 8 Pin J
Illustration 7 g06123890
Work tool electrical connector - socket identification
Illustration 8 g06124895
Determine which cab controls you want to energize the control solenoids on the work tool. If the work tool utilizes the Delphi-style electrical connector, connect a solenoid jumper Work Tool Harness As. (4) to each solenoid plug used via the work tool solenoid connections (C). Refer to the connector identification in Table 2 and the Illustration 4 through Illustration 8 to identify the available machine electrical output controls.
Connect a solenoid jumper Harness As. (4) to each work tool solenoid being controlled.If the work tool solenoids use Deutsch-style electrical connectors, make the connections via the Work Tool Solenoid Connections (C) directly.
Route the harness safely along the work tool, being careful to allow for flex joints. Avoid a routing that would put strain on the wires at a connector. Avoid a routing that would put the harness in contact with moving parts or pinch points on the work tool. Provide enough slack in the harness such that the 14-Pin Machine Connector (D) is able to reach the host machine work tool electrical connector. Ensure that the harness can move freely within the range of expected work tool movement.
Secure the harness to the work tool frame using tie straps and/or p-clips in a manner that best keeps the harness free from contact with the environment including limbs, rocks, generated airborne debris, and so on.Refer to the addendum that follows for more installation detail on certain specific non-Cat work tools.Addendum: Installation & Operation Procedure for Specific non-Cat Work Tools
24 in Bobcat© Fast Cut Asphalt Planar (6 Function)Installation
Disconnect attachment from machine and unhook hydraulic/electrical lines.
Illustration 9 g06124795
(G) Hydraulic valve retaining hardware. Requires a 14mm socket.
(J) Hydraulic line. Requires a 7/8 inch wrench.
(K) Hydraulic lines. Requires a 1 1/4 inch wrench.
Loosen and remove the 3 feed/return lines from the attachment on the back side of the planer
Illustration 10 g06124798
(H) Bolt and nut combination. Requires a 14mm wrench/socket combination.
Illustration 11 g06124694
(H) Bolt and nut combination. Requires a 14mm wrench/socket combination.
Loosen and remove 3 bolts/nuts from bracket using a 14 mm socket and wrench
Loosen and remove 3 bolts from the valve body
Illustration 12 g06124360
Reinstall valve body onto the frame of the attachment and tighten 3 bolts using 14mm socket
Illustration 13 g06124363
Unplug connectors from each solenoid:
Illustration 14 g06124366
Connect the solenoid jumper Harness As. (4) to the work tool solenoids:
Reinstall the ECM bracket & secure the OEM harness to the work tool.
Moving from left to right, facing solenoids, verify that wire placement corresponds:
Cut depth left (Far left solenoid)
Top coil = M914-WH (from Work Tool Harness As. (1))
Bottom coil = M909–GN (from Work Tool Harness As. (1))
Cut depth right (Middle solenoid)
Top coil = M911-YL (from Work Tool Harness As. (1))
Bottom coil = M910–OR (from Work Tool Harness As. (1))
Side-shift (Right solenoid)
Top coil = H759-OR (from Work Tool Harness As. (2))
Bottom coil = H758–BR (from Work Tool Harness As. (2))
Far right solenoid can be left alone.Operation
The thumb roller on the right joystick is to operate the cold planer drum.
Push