7F9543 COLLAR Caterpillar parts
160H NA, 55, 561B, 561C, 561M, 561N, 57, 572R, 572R II, 611, 615, 615C, 824B, 824H, 834, 977, 977D, 977L, 983, 983B, D4H, D5, D5B, D5H, D5M, D5N, D5R LGP, D6C, D6D, D6E SR, D6F SR, D6G, D6G SR, D6G2 L...
Rating:
Alternative (cross code) number:
CA7F9543
7F-9543
7F9543
CA7F9543
7F-9543
7F9543
Weight: 0.010 pounds 0 kg.
MOTOR GRADER, WINCH,
Compatible equipment models: 7F9543:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-2244     Pump Extractor     1    
B     6V-4186     Fuel Pump Timing Pin     1    
C     8T-5287     Wrench     1    
D     6V-9128     Rack Position Tool Group    
1    
3S-3270 Indicator Contact Point     1    
C-clamp 1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00507964
Install spacer (1) in the fuel injection pump housing.
Illustration 2 g00507989
Illustration 3 g00508002
Install Tool (B) in the fuel injection pump housing. Move the rack until Tool (B) can be installed in order to hold the rack in the center position. The rack must be in the center position in order to install the fuel injection pumps.
Turn the camshaft until the lobe of the camshaft is downward so that the fuel injection pump can be installed.
Install Tool (A) on the bonnet of the fuel injection pump.
Install the fuel injection pump in the fuel injection pump housing. Ensure that slot (3) that is cut in the gear is aligned with the small pin (2) and groove (4) in the barrel. The small pin (2) and groove (4) in the barrel are aligned with dowel (5) in the fuel injection pump housing.
Illustration 4 g00508005
Put clean engine oil on O-ring seal (6) and install the O-ring seal in the fuel injection pump housing.
Illustration 5 g00508057
Install bushing (7) by hand until the bushing is even with the top of the fuel injection pump housing. If bushing (7) cannot be installed by hand, remove bushing (7). Remove the fuel injection pump. Put the pump in alignment and reinstall bushing (7) .
Install Tool (C) on bushing (7) and tighten the bushing to a torque of 163 14 N m (120 10 lb ft).
Install Tool (D) in order to measure the total travel of the rack. The correct travel for the rack is 15.70 mm (.618 inch). A smaller measurement is an indication of improper fuel injection pump installation.
Repeat Steps 1 through 9 in order to install the remaining fuel injection pumps.
Install the cover and the gasket on the fuel injection pump housing.
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-2244     Pump Extractor     1    
B     6V-4186     Fuel Pump Timing Pin     1    
C     8T-5287     Wrench     1    
D     6V-9128     Rack Position Tool Group    
1    
3S-3270 Indicator Contact Point     1    
C-clamp 1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00507964
Install spacer (1) in the fuel injection pump housing.
Illustration 2 g00507989
Illustration 3 g00508002
Install Tool (B) in the fuel injection pump housing. Move the rack until Tool (B) can be installed in order to hold the rack in the center position. The rack must be in the center position in order to install the fuel injection pumps.
Turn the camshaft until the lobe of the camshaft is downward so that the fuel injection pump can be installed.
Install Tool (A) on the bonnet of the fuel injection pump.
Install the fuel injection pump in the fuel injection pump housing. Ensure that slot (3) that is cut in the gear is aligned with the small pin (2) and groove (4) in the barrel. The small pin (2) and groove (4) in the barrel are aligned with dowel (5) in the fuel injection pump housing.
Illustration 4 g00508005
Put clean engine oil on O-ring seal (6) and install the O-ring seal in the fuel injection pump housing.
Illustration 5 g00508057
Install bushing (7) by hand until the bushing is even with the top of the fuel injection pump housing. If bushing (7) cannot be installed by hand, remove bushing (7). Remove the fuel injection pump. Put the pump in alignment and reinstall bushing (7) .
Install Tool (C) on bushing (7) and tighten the bushing to a torque of 163 14 N m (120 10 lb ft).
Install Tool (D) in order to measure the total travel of the rack. The correct travel for the rack is 15.70 mm (.618 inch). A smaller measurement is an indication of improper fuel injection pump installation.
Repeat Steps 1 through 9 in order to install the remaining fuel injection pumps.
Install the cover and the gasket on the fuel injection pump housing.
Cat SIS web machinery list:
Parts collar Caterpillar catalog:
3J1943
COLLAR
5S, 6A, 7A, D6D, D6E, D6E SR, D6G SR, D7G
5S, 6A, 7A, D6D, D6E, D6E SR, D6G SR, D7G
5F0707
COLLAR
5S, 6A, 977H, D5B, D5E
5S, 6A, 977H, D5B, D5E
1609756
COLLAR
561M, 561N, D5M, D5N, D5R LGP, D6M, D6N, D6N LGP, D6N OEM, PM-201, PM-565, PM-565B
561M, 561N, D5M, D5N, D5R LGP, D6M, D6N, D6N LGP, D6N OEM, PM-201, PM-565, PM-565B
7M5050
COLLAR
561B, 561C, D5
561B, 561C, D5
6B4978
COLLAR
561B, 561C, 977D, 977H, D5
561B, 561C, 977D, 977H, D5
9S4323
COLLAR ASSEM.
583K, 983, D8H, D8K
583K, 983, D8H, D8K
7M1849
COLLAR ASSEM.
955K, 955L, D6C, D6D
955K, 955L, D6C, D6D
7G1904
COLLAR ASSEM.
571G, 572G, 977K, 977L, D7G
571G, 572G, 977K, 977L, D7G
1J6751
COLLAR
7A, 8A, D7G
7A, 8A, D7G
2D7688
COLLAR
615, 621, 623
615, 621, 623
2V4331
COLLAR
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 525B, 528, 528B, 530B, 533, 535B, 543, 545, 950, HA770, HA771,...
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 525B, 528, 528B, 530B, 533, 535B, 543, 545, 950, HA770, HA771,...
5B0577
COLLAR
120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 14...
120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 14...
1548345
COLLAR & PIN AS
D10R, D6R, D7R, D8R
D10R, D6R, D7R, D8R
2Q3386
COLLAR
836, D10R, D6R, D7R, D8R, D9N, D9R
836, D10R, D6R, D7R, D8R, D9N, D9R
1336790
COLLAR
315B FM L
315B FM L
1028081
COLLAR
307B
307B
0963927
COLLAR
307, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300B, E70, E70B, EL240B
307, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300B, E70, E70B, EL240B
0963924
COLLAR
307, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300B, E70, E70B, EL240B
307, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300B, E70, E70B, EL240B
6F0944
COLLAR
931B, 931C, 931C II, 933, 939, 943, 953, 953B, 953C, 963, 963B, 963C, 963D, 973, 973C, D3B, D3C, D3C II, D3C III, D4C, D4C III, D5C, D5C III
931B, 931C, 931C II, 933, 939, 943, 953, 953B, 953C, 963, 963B, 963C, 963D, 973, 973C, D3B, D3C, D3C II, D3C III, D4C, D4C III, D5C, D5C III
1346638
COLLAR-TRACK
973, 973C, 973D
973, 973C, 973D
1240570
COLLAR
953C, 963C, 973C
953C, 963C, 973C
1205785
COLLAR-END
527, 963, 963B, 963C, 963D, D6G, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D6T LGP
527, 963, 963B, 963C, 963D, D6G, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D6T LGP
1671951
COLLAR
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
1073945
COLLAR-SEAL
527, 572R, 572R II, 583R, 583T, 587R, 587T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7H, D7R, D7R II, D7R XR, D8R, D8R II, D8T, D9N, D9R, D9T, PL83, PL87
527, 572R, 572R II, 583R, 583T, 587R, 587T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7H, D7R, D7R II, D7R XR, D8R, D8R II, D8T, D9N, D9R, D9T, PL83, PL87