COLLET 8R3931 - Caterpillar

8R3931 COLLET Caterpillar parts 992C, 992D, 994, 994D, 994F, 994H, R1600, R1600G, R1600H, R1700 II, R1700G

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA8R3931
8R-3931
8R3931

Weight: 18 pounds 8 kg.

Buy COLLET 8R3931 Caterpillar genuine, new aftermarket tractor parts with delivery
LOAD HAUL DUMP, WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

8R3931 Collet - Fits: 992D 994 994D 992C 994F R1700G

$125.00

05 Jun 2022

Amazon.com

8R3931 Collet - Fits: 992D 994 994D 992C 994F R1700G
CGR Compatible Models - 992D 994 994D 992C 994F R1700G || Interchange - 1V8039 || CONTROL GP || Country of origin: Italy

$105.60

09 Jan 2019

CATERPILLAR AFTERMARKET: CATERPILLAR AFT

Caterpillar Collet 8R3931 New

$103.25

10 Feb 2022
19.0479[8.57] Pounds
US: IronDT

Caterpillar COLLET (8R3931) New Aftermarket By CTP
CTP

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#722127 8R3931

2021-09-20

Number on catalog scheme: 20

For full view, you need register

Compatible equipment models: 8R3931:

LOAD HAUL DUMP R1600 R1600G R1600H R1700 II R1700G

WHEEL LOADER 992C 992D 994 994D 994F 994H Caterpillar

Information:

Illustration 1 g00690844
(1) Diameter of bore in cylinder block for piston ... 97.000 to 97.025 mm (3.8189 to 3.8199 inch)Maximum permissible wear in the cylinder bore ... 0.25 mm (0.010 inch) (2) Height between top and bottom faces ... 360.925 to 361.075 mm (14.2096 to 14.2155 inch) (3) Rear oil sealWhen the rear oil seal is installed, put engine oil on the lip of the seal. The rear oil seal is correctly installed when the seal face extends 1.5 mm (0.06 inch) from the rear face of the cylinder block. (4) Diameter of the bore in the cylinder block for the number one journal of the camshaft front bearing ... 51.84 to 51.87 mm (2.041 to 2.042 inch)Note: Ensure that the oil holes in the bearing are aligned with the oil holes in the cylinder block.Diameter of the bore in the cylinder block for numbers two, three, four and five journals of the camshaft ... 48.025 to 48.050 mm (1.8907 to 1.8917 inch) (5) Camshaft front bearing (6) Diameter of bores in cylinder block for main bearings ... 69.000 to 69.019 mm (2.7165 to 2.7173 inch) (7) Tighten the bolts for the main bearing caps to the following torque. ... 147 N m (108 lb ft)Note: Apply a small amount of 8T-9022 Silicone Gasket to the corners of the cylinder block for the rear main bearing cap. After the rear main bearing cap is installed, remove any excess sealant from the inside of the recess for the rear oil seal. Excess sealant prevents the correct seating of the rear oil seal.
Illustration 2 g00690856
Main bearing caps for the crankshaft (8) The rear main bearing cap is not marked. (9) Numbers 2 through 4 main bearing caps have an arrow and a number. The arrow points to the front of the engine. The number indicates the position. (10) The front main bearing cap is number 1.
Illustration 3 g00386798
(11) Seal for the front and rear main bearing caps. (12) The seals for the front and the rear main bearing caps have a curve at one end. The curved side must be installed toward the side of the engine. The curved end is inserted first into the hole. (13) Before installing the seals, inject a small quantity of 8T-9022 Silicone Gasket in the holes for the seals.
Illustration 4 g00690809
(14) Seal for the front main bearing cap.