1U9347 COMPRESSOR GP- Caterpillar parts
Rating:
Alternative (cross code) number:
CA1U9347
1U-9347
1U9347
CA1U9347
1U-9347
1U9347
Weight: 9 pounds 4 kg.
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 452-6006 Grease - Start By:
Remove the bucket.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06317902
Park the machine on a hard, level surface. Fully extend the stick.
Extend the bucket cylinder out completely to rest bucket linkage (1) on a flat surface.
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Install a suitable cribbing under the bucket cylinder.
Illustration 2 g06317903
Illustration 3 g06317904
Attach a suitable lifting device to bucket linkage (1). The weight of bucket linkage (1) is approximately 80 kg (176 lb).
Remove bolt (2), outside nut (3B), and inside nut (3A).
Attach suitable lifting device to links (4) to lower links (4) after bucket linkage (1) is removed.
Remove pin (5) and bucket linkage (1).
Illustration 4 g06317905
Remove bolt (6), outside nut (7A), and inside nut (7B).
Remove pin (8) and links (4).Installation Procedure
Install the bucket linkage in the reverse order of removal.
Coat all bores for the pins with Tooling (A).
When installing the bucket linkage assembly, rotate the rod end of the bucket cylinder to position grease fitting away from the stick.
Illustration 5 g02763340
Install bolt (6), inside nut (7B), and outside nut (7A) that secure pin (8). Position outside nut (7A) until outside nut (7A) is 0.50 mm (0.019 inch) past end of bolt (6). Tighten inside nut (7B) against outside nut (7A) to a torque of 175 30 N.m (129 22 lb ft).
Install bolt (2), inside nut (3A), and outside nut (3B) that secure pin (5). Position outside nut (3B) until outside nut (3B) is 0.50 mm (0.019 inch) past end of bolt (2). Tighten inside nut (3A) against outside nut (3B) to a torque of 175 30 N.m (129 22 lb ft).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 452-6006 Grease - Start By:
Remove the bucket.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06317902
Park the machine on a hard, level surface. Fully extend the stick.
Extend the bucket cylinder out completely to rest bucket linkage (1) on a flat surface.
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Install a suitable cribbing under the bucket cylinder.
Illustration 2 g06317903
Illustration 3 g06317904
Attach a suitable lifting device to bucket linkage (1). The weight of bucket linkage (1) is approximately 80 kg (176 lb).
Remove bolt (2), outside nut (3B), and inside nut (3A).
Attach suitable lifting device to links (4) to lower links (4) after bucket linkage (1) is removed.
Remove pin (5) and bucket linkage (1).
Illustration 4 g06317905
Remove bolt (6), outside nut (7A), and inside nut (7B).
Remove pin (8) and links (4).Installation Procedure
Install the bucket linkage in the reverse order of removal.
Coat all bores for the pins with Tooling (A).
When installing the bucket linkage assembly, rotate the rod end of the bucket cylinder to position grease fitting away from the stick.
Illustration 5 g02763340
Install bolt (6), inside nut (7B), and outside nut (7A) that secure pin (8). Position outside nut (7A) until outside nut (7A) is 0.50 mm (0.019 inch) past end of bolt (6). Tighten inside nut (7B) against outside nut (7A) to a torque of 175 30 N.m (129 22 lb ft).
Install bolt (2), inside nut (3A), and outside nut (3B) that secure pin (5). Position outside nut (3B) until outside nut (3B) is 0.50 mm (0.019 inch) past end of bolt (2). Tighten inside nut (3A) against outside nut (3B) to a torque of 175 30 N.m (129 22 lb ft).
Parts compressor Caterpillar catalog:
1U9162
COMPRESSOR GP-
Caterpillar
Caterpillar
1U9089
COMPRESSOR-
Caterpillar
Caterpillar
1U8472
COMPRESSOR
Caterpillar
Caterpillar
1U8471
COMPRESSOR
Caterpillar
Caterpillar
1U8453
COMPRESSOR
Caterpillar
Caterpillar
1U8452
COMPRESSOR
Caterpillar
Caterpillar
2013834
COMPRESSOR GP
Caterpillar
Caterpillar
2004422
COMPRESSOR GP
Caterpillar
Caterpillar
2003914
COMPRESSOR-
Caterpillar
Caterpillar
1Y7426
COMPRESSOR
Caterpillar
Caterpillar
1W9877
COMPRESSOR G-
Caterpillar
Caterpillar
1W8907
COMPRESSOR G-
Caterpillar
Caterpillar