7E5805 COMPRESSOR GP-REFRIGERANT Caterpillar parts
225D, 231D
Rating:
Alternative (cross code) number:
CA7E5805
7E-5805
7E5805
CA7E5805
7E-5805
7E5805
Weight: 0.08 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
For full view, you need register
Information:
Heaters
Note: Oil pan immersion heaters are not recommended for heating the lube oil. To ensure the compatibility of the components, only use equipment that is recommended by Caterpillar.Startability will be improved at temperatures below 12 °C (55 °F) with a starting aid. A jacket water heater may be needed and/or the crankcase oil may need to be warmed.Note: The fluid that is heated must be continuously circulated. This will help to prevent localized overheating of the fluid.A jacket water heater is available as an option for starting in temperatures as low as 0 °C (32 °F). The jacket water heater can maintain the water temperature at approximately 32 °C (90 °F). The heated water will help to keep the oil in the engine block warm enough to flow when the engine is started.When No. 2 diesel fuel is used, a fuel heater will maintain the temperature of the fuel above the cloud point. Fuel line insulation will help to maintain the fuel temperature.Consult your Caterpillar dealer for more information on the starting aids that are available for cold weather starting.Electric Starting Motor
Maintain the proper level of electrolyte in the batteries. Keep the batteries fully charged.To maximize the battery power, heat the battery compartment or store the batteries in a warm location. Typically, batteries only have 50 percent of the capability at −10 °C (14 °F) versus 27 °C (80 °F).Extra battery capacity may be necessary for very cold temperatures.Air Starting Motor
Note: The maximum air pressure for starting must not exceed 1030 kPa (150 psi).To start the engine at colder temperatures, the following conditions may be necessary:
Maximum air pressure for the starting motor
An additional volume of airStarting With Ether
Personal injury or property damage can result from alcohol or starting fluids.Alcohol or starting fluids are highly flammable and toxic and if improperly stored could result in injury or property damage.
The optional ether starting aid is the only system that is recommended for the injection of starting fluid.Perform the procedures that are described in this Operation and Maintenance Manual, "Before Starting Engine" topic (Operation Section).
Ensure that the driven equipment is unloaded. Place the transmission in neutral.
Move the throttle so that fuel is provided to the engine.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine. Use of the starting aid depends on these conditions:
The engine control module controls the duration of automatic ether injection in these circumstances:
The starting aid is in the automatic mode.
The jacket water temperature is between 10 to −40 °C (50 to −40 °F).
The engine rpm is more than 30 rpm and less than 1500 rpm.
Manual ether injection can be performed in these circumstances:
The starting aid is in the manual mode.
The jacket water temperature is between 50 to 66 °C (50 to 166 °F).
The engine rpm is more than 30 rpm and less than 1500 rpm.
Excessive starting fluid can cause piston and ring damage.Use starting fluid for cold starting purposes only.Do
Note: Oil pan immersion heaters are not recommended for heating the lube oil. To ensure the compatibility of the components, only use equipment that is recommended by Caterpillar.Startability will be improved at temperatures below 12 °C (55 °F) with a starting aid. A jacket water heater may be needed and/or the crankcase oil may need to be warmed.Note: The fluid that is heated must be continuously circulated. This will help to prevent localized overheating of the fluid.A jacket water heater is available as an option for starting in temperatures as low as 0 °C (32 °F). The jacket water heater can maintain the water temperature at approximately 32 °C (90 °F). The heated water will help to keep the oil in the engine block warm enough to flow when the engine is started.When No. 2 diesel fuel is used, a fuel heater will maintain the temperature of the fuel above the cloud point. Fuel line insulation will help to maintain the fuel temperature.Consult your Caterpillar dealer for more information on the starting aids that are available for cold weather starting.Electric Starting Motor
Maintain the proper level of electrolyte in the batteries. Keep the batteries fully charged.To maximize the battery power, heat the battery compartment or store the batteries in a warm location. Typically, batteries only have 50 percent of the capability at −10 °C (14 °F) versus 27 °C (80 °F).Extra battery capacity may be necessary for very cold temperatures.Air Starting Motor
Note: The maximum air pressure for starting must not exceed 1030 kPa (150 psi).To start the engine at colder temperatures, the following conditions may be necessary:
Maximum air pressure for the starting motor
An additional volume of airStarting With Ether
Personal injury or property damage can result from alcohol or starting fluids.Alcohol or starting fluids are highly flammable and toxic and if improperly stored could result in injury or property damage.
The optional ether starting aid is the only system that is recommended for the injection of starting fluid.Perform the procedures that are described in this Operation and Maintenance Manual, "Before Starting Engine" topic (Operation Section).
Ensure that the driven equipment is unloaded. Place the transmission in neutral.
Move the throttle so that fuel is provided to the engine.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine. Use of the starting aid depends on these conditions:
The engine control module controls the duration of automatic ether injection in these circumstances:
The starting aid is in the automatic mode.
The jacket water temperature is between 10 to −40 °C (50 to −40 °F).
The engine rpm is more than 30 rpm and less than 1500 rpm.
Manual ether injection can be performed in these circumstances:
The starting aid is in the manual mode.
The jacket water temperature is between 50 to 66 °C (50 to 166 °F).
The engine rpm is more than 30 rpm and less than 1500 rpm.
Excessive starting fluid can cause piston and ring damage.Use starting fluid for cold starting purposes only.Do
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts compressor Caterpillar catalog:
1561821
COMPRESSOR GP-REFRIGERANT
950G, 962G, IT62G
950G, 962G, IT62G
2525565
COMPRESSOR GP-REFRIGERANT
C7, C9, CX31-C9I, TH31-E61
C7, C9, CX31-C9I, TH31-E61
312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 316E L, 318D2 L, 318E L
312E, 312E L, 316E L
3794415
COMPRESSOR GP-REFRIGERANT
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
3594326
COMPRESSOR GP-REFRIGERANT
C27, C32
C27, C32
3777601
COMPRESSOR & MTG GP-REFRIG
906H2, 907H2, 908H2
906H2, 907H2, 908H2
2W9776
COMPRESSOR GP-REFRIGERANT
416, 426, 428
416, 426, 428
2041547
COMPRESSOR GP-REFRIGERANT
3126B, C-9
3126B, C-9
4255317
COMPRESSOR GP-REFRIGERANT
PL83, PL87
PL83, PL87
910E, IT12B, IT14F