0034998 CONE AND ROLLERS,TA BRAKE SHAFT Caterpillar parts
D7F
Rating:
Alternative (cross code) number:
CA0034998
003-4998
0034998
CA0034998
003-4998
0034998
Weight: 12 pounds 5 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 0034998:
Number on catalog scheme:
9
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-5527(1) Cylinder Pack Puller 1
1U-9897(1) Bridge 1
B 2P-8260 Cylinder Liner Installer 1
C 5P-3975 Rubber Lubricant 1
(1) 5P-8665 Cylinder Liner Puller Gp is an optional Tool for removing the cylinder liner.Start By:
Remove the pistons and connecting rods.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01138987
Use Tooling (A) to remove cylinder liners (1).
Remove the seals from cylinder liners (1). Installation Procedure
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection - Inspect".
Illustration 2 g01139009
Apply Tooling (C) to new seal (2). Install new seal (2) in the machined groove on cylinder liner (1).
Lubricate the lower portion of cylinder liner (1) with clean engine oil. Ensure that the corresponding crankshaft throw is at the bottom center. Use Tooling (B) to install cylinder liner (1). End By:
Install the pistons and connecting rods.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 173-5527(1) Cylinder Pack Puller 1
1U-9897(1) Bridge 1
B 2P-8260 Cylinder Liner Installer 1
C 5P-3975 Rubber Lubricant 1
(1) 5P-8665 Cylinder Liner Puller Gp is an optional Tool for removing the cylinder liner.Start By:
Remove the pistons and connecting rods.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01138987
Use Tooling (A) to remove cylinder liners (1).
Remove the seals from cylinder liners (1). Installation Procedure
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection - Inspect".
Illustration 2 g01139009
Apply Tooling (C) to new seal (2). Install new seal (2) in the machined groove on cylinder liner (1).
Lubricate the lower portion of cylinder liner (1) with clean engine oil. Ensure that the corresponding crankshaft throw is at the bottom center. Use Tooling (B) to install cylinder liner (1). End By:
Install the pistons and connecting rods.
Caterpillar parts catalog:
Parts cone Caterpillar catalog:
627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 776C, 776D, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 793B, D364, D375D, D397D, D7F
235D, 245, 245B, 245D, 2864C, 571G, 572G, 586C, 844, 844H, 844K, 854G, 854K, 955K, 955L, 983, 983B, 990, 990 II, 990H, 990K, 992G, 992K, BR624, D10T, D10T2, D7F, D7G, D7G2, D9R, D9T, HF201, HF201B, HF...
120, 120B, 12E, 140, 140B, 518, 518C, 528, 528B, 530B, 561B, 561C, 572G, 941, 951B, 955C, 955H, 955K, 955L, 977D, 977H, 983, D4D, D4E, D4E SR, D5, D5B, D5E, D7E, D7E LGP, D7F, D7G
613, 613B, 920, 930, 977D, 977H, 977K, D7F
571G, 572G, 983, 983B, D7F, D7G, D7G2, PM-565, PR-1000, PR-450, PR-450C
977D, D7F
824, 824B, 834
D9E
824C, TA19-M4WD, TA22-M4WD
D9L
120, 120B, 12E, 12F, 140B, 14E, D7G, D7G2
14G, 16G
330, 330 FM L, 330 L, 330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 350, OEMS
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G