2P8353 CONE-BEARING Caterpillar parts
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 836, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 988B, 988F, AD30, AD40, AD45, AD45B, AE40, AE40 II, R1700G
Rating:
Alternative (cross code) number:
CA2P8353
2P-8353
2P8353
CA2P8353
2P-8353
2P8353
Weight: 13 pounds 5 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$398.20
27 Mar 2024
US: FinditParts Inc
2P8353 - CONE-BEARING fits Caterpillar (CAT)
BLUMAQ
BLUMAQ
$363.06
05 Feb 2024
Amazon.com
CTP 2P8353 Tapred Roller Cone Bearing for Models 824G/824G II/824H/824K/825G/825G II/825H/825K/826G/826G II/826H Caterpillar
CTP Use for Models 824G/824G II/824H/824K/825G/825G II/825H/825K/826G/826G II/826H Caterpillar || Sold in each || Easy in-and-out fit
CTP Use for Models 824G/824G II/824H/824K/825G/825G II/825H/825K/826G/826G II/826H Caterpillar || Sold in each || Easy in-and-out fit
$422.42
31 Jan 2024
US: FinditParts Inc
2P8353 - CONE-BEARING fits Caterpillar (CAT)
BLUMAQ 2P8353 - CONE-BEARING fits Caterpillar (CAT)
BLUMAQ 2P8353 - CONE-BEARING fits Caterpillar (CAT)
This part in 2 request:
Show.
This information for suppliers only!
2021-01-20
2019-06-25
Number on catalog scheme:
3
For full view, you need register
Compatible equipment models: 2P8353:
Information:
3200, 3300, 3400, 3500 Series EnginesThe new seal groups are quite different from the former standard lip-type seals. The difference is the hydrodynamic grooves in the sealing lip of the new seal. These grooves in the seal lip move lubrication oil back into the engine crankcase as the crankshaft turns. Because of this seal lip design, the front seal for an engine is different from the rear seal group. The installed position of the seal lip grooves is important, because the grooves are very sensitive to the direction of crankshaft rotation. Each seal is marked with an arrow to show the direction of shaft rotation for which the seal can be used. If a specific seal group is installed on the wrong end of an engine, lubrication oil can actually be taken out of an engine, because the grooves in the seal lip are in the wrong direction in relation to crankshaft rotation. Special handling procedures and seal installation instructions for specific engines are given on the pages that follow.1 Use The Correct Tools For Seal Group Installation
Some additional new tools, along with some existing tools, are needed to install the seal groups. Be sure to use the correct installation tools to maintain the necessary seal-to-wear sleeve relationship.2 Separation Of The Seal From The Sleeve Is Not Permissible
The material in the large lip of the seal can be damaged easily. Fingers, fingernails, wires or the edge of the sleeve can put a scratch on the surface of the seal lip. It is possible that a scratch or a rub (which can not be seen) from a finger, can damage the seal enough that it can not be used. In these seal groups, the sleeve is installed in the seal, by the seal group supplier, for two very good reasons, as follows:A. To give better protection to the special material on the seal lip.B. To make for easier installation. The seal and the sleeve are installed, both at the same time.3 Once There Is Separation Of A Seal And Sleeve, They Must Not Be Used Again
Once there is separation of a sleeve and seal, one from the other, they can not be used again. When you try to put the seal on the sleeve, or the sleeve in the seal, the sleeve will always damage the seal, and neither part can be used again. Always install a new seal group if there is
Some additional new tools, along with some existing tools, are needed to install the seal groups. Be sure to use the correct installation tools to maintain the necessary seal-to-wear sleeve relationship.2 Separation Of The Seal From The Sleeve Is Not Permissible
The material in the large lip of the seal can be damaged easily. Fingers, fingernails, wires or the edge of the sleeve can put a scratch on the surface of the seal lip. It is possible that a scratch or a rub (which can not be seen) from a finger, can damage the seal enough that it can not be used. In these seal groups, the sleeve is installed in the seal, by the seal group supplier, for two very good reasons, as follows:A. To give better protection to the special material on the seal lip.B. To make for easier installation. The seal and the sleeve are installed, both at the same time.3 Once There Is Separation Of A Seal And Sleeve, They Must Not Be Used Again
Once there is separation of a sleeve and seal, one from the other, they can not be used again. When you try to put the seal on the sleeve, or the sleeve in the seal, the sleeve will always damage the seal, and neither part can be used again. Always install a new seal group if there is
Cat SIS web machinery list:
Parts cone Caterpillar catalog:
594, 594H, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 993K, 994, 994D, 994F, 994H, AD30, D9E, D9G, D9H, R1700G
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 966G, 966G II, 966H, 966K, 972G, 972G II, 972H, 972K, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 986H, 992, AD30,...
613, 613B, 814, 815, 824, 824B, 824K, 825B, 825K, 826K, 834, 950, 966C, 980K, 980K HLG, 980M, 982M, 986H, 988, 992
16G, 16H, 16H NA, 16M, 24H, 24M, 824C, 824H, 824K, 825H, 825K, 826C, 826H, 826K, 834B, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 988B, 988F II, 993K, AD40, AE40, D44B, D550...
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980H, 980K, 980K HLG, 980M, 982M, 986H, 988F, 988F II, 988G, 988H, 988K,...
24H, 24M, 834B, 834G, 834H, 836, 836G, 836H, 988G, 988H, 992C, 992D, AD30, AD45, AD45B, AD55, AD55B, AD60, AE40 II, D11R, D11T, R2900, R2900G
24H, 24M, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 986H, 988G, 988H, 988K, AD30, AD45, AD45B, AD55, AD55B, AD60, AE40 II, R2900, R2900G, R3000H, RM-500
834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, AE40 II, R2900, R2900G, R3000H
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824K, 825K, 826K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972K, 972M, 972M XE
834, 834B, 836, 988F, 988F II, 992
834B, 836, 986H, 988F II
834B, 836, 986H, 988F II
16G, 16H, 16H NA, 16M, 24H, 24M, 824C, 824H, 824K, 825H, 825K, 826C, 826H, 826K, 834B, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, 988B, 988F II, 993K, AD40, AE40, D44B, D550...
2J7138
CONE
24M, 651, 844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K
24M, 651, 844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K
4J7428
CONE
651
651
2J8913
CONE
630A, 994
630A, 994
2J8914
CONE
630A, 834B, 994F, 994H, D10, D11N, D11R
630A, 834B, 994F, 994H, D10, D11N, D11R
508, 518, 936, D250B, D250E, D300B, D300D, G936
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980H, 980K, 980K HLG, 980M, 982M, 986H, 988F, 988F II, 988G, 988H, 988K,...
24H, 24M, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992G, 992K
844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K
9U9662
CONE-ROLLER BEARING
844, 844H, 844K, 990, 990 II, 990H, 990K
844, 844H, 844K, 990, 990 II, 990H, 990K
5P8043
CONE-ROLLER BEARING
24H, 844, 844H, 854G, 990, 990 II, 992C, 992D, 992G
24H, 844, 844H, 854G, 990, 990 II, 992C, 992D, 992G
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 994, 994D, 994F, 994H