4B5180 CONE Caterpillar parts
120, 120B, 12E, 140, 140B
Rating:
Alternative (cross code) number:
CA4B5180
4B-5180
4B5180
CA4B5180
4B-5180
4B5180
Weight: 2 pounds 0 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$32.03
28 Nov 2022
Amazon.com
CTP 4B5180 Tapred Roller Cone Bearing for Models 120/120B/12E/140/140B Caterpillar
CTP Use for Models 120/120B/12E/140/140B Caterpillar || Sold in each || Easy in-and-out fit
CTP Use for Models 120/120B/12E/140/140B Caterpillar || Sold in each || Easy in-and-out fit
$37.21
13 Jul 2022
US: Florida-Parts-Z
4B5180 - Cone for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$31.38
13 Jul 2022
Amazon.com
CTP 4B5180 Tapred Roller Cone Bearing for Models 120/120B/12E/140/140B Caterpillar
CTP Use for Models 120/120B/12E/140/140B Caterpillar || Sold in each || Easy in-and-out fit
CTP Use for Models 120/120B/12E/140/140B Caterpillar || Sold in each || Easy in-and-out fit
Number on catalog scheme:
None
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 390-1131 Crankshaft Locking Pin 1
B - Balancer Timing Pin
(Bolt M8 by 22mm) 1
C - Technologic 15 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Check that the balancer drive gear is not worn or damaged. If necessary, replace the balancer drive gear.
Illustration 1 g02887016
Illustration 2 g02893017
Illustration 3 g02709625
Install Tooling (A) into Position (X) in the cylinder block. Tooling (A) must be located in Position (Y) in the crankshaft. Note: Ensure that Tooling (A) is located in the correct drilling in the crankshaft as shown in Illustration 1.Note: Failure to locate the crankshaft in the correct position will cause severe engine damage.
Ensure that Tooling (B) is installed to balancer (4). Note: New balancers will be supplied with Tooling (B) in position.
If necessary, install dowels (9) to balancer (4).
Attach a suitable lifting device to the balancer. The weight is approximately 15 kg (33 lb).
Use the suitable lifting device in order to install the balancer to the cylinder block.
Install bolts (5) to the balancer. Tighten the bolts to a torque of 70 N m (52 lb ft).
Remove the suitable lifting device from the balancer.
Install a new O-ring seal (8) onto suction pipe (3). Install the suction pipe assembly to the cylinder block.
Apply Tooling (C) onto the threads of bolt (7). Install bolt (7) finger tight.
Apply Tooling (C) onto the threads of bolts (6). Install bolts (6) finger tight.
Tighten bolt (7) to a torque of 10 N m (89 lb in)
When M8 bolts are installed, tighten bolts (6) to a torque of 25 N m (221 lb in). When M10 bolts are installed, tighten bolts (6) to a torque of 45 N m (33 lb ft).
Remove Tooling (B) from Position (Z) in the balancer.
Remove Tooling (A) from Position (X) in the cylinder block.
Install a new O-ring seal (1) to plug (2). Install plug (2) into Position (X) in the cylinder block. Tighten the plug to a torque of 50 N m (37 lb ft). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Name Qty
A 390-1131 Crankshaft Locking Pin 1
B - Balancer Timing Pin
(Bolt M8 by 22mm) 1
C - Technologic 15 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.
Check that the balancer drive gear is not worn or damaged. If necessary, replace the balancer drive gear.
Illustration 1 g02887016
Illustration 2 g02893017
Illustration 3 g02709625
Install Tooling (A) into Position (X) in the cylinder block. Tooling (A) must be located in Position (Y) in the crankshaft. Note: Ensure that Tooling (A) is located in the correct drilling in the crankshaft as shown in Illustration 1.Note: Failure to locate the crankshaft in the correct position will cause severe engine damage.
Ensure that Tooling (B) is installed to balancer (4). Note: New balancers will be supplied with Tooling (B) in position.
If necessary, install dowels (9) to balancer (4).
Attach a suitable lifting device to the balancer. The weight is approximately 15 kg (33 lb).
Use the suitable lifting device in order to install the balancer to the cylinder block.
Install bolts (5) to the balancer. Tighten the bolts to a torque of 70 N m (52 lb ft).
Remove the suitable lifting device from the balancer.
Install a new O-ring seal (8) onto suction pipe (3). Install the suction pipe assembly to the cylinder block.
Apply Tooling (C) onto the threads of bolt (7). Install bolt (7) finger tight.
Apply Tooling (C) onto the threads of bolts (6). Install bolts (6) finger tight.
Tighten bolt (7) to a torque of 10 N m (89 lb in)
When M8 bolts are installed, tighten bolts (6) to a torque of 25 N m (221 lb in). When M10 bolts are installed, tighten bolts (6) to a torque of 45 N m (33 lb ft).
Remove Tooling (B) from Position (Z) in the balancer.
Remove Tooling (A) from Position (X) in the cylinder block.
Install a new O-ring seal (1) to plug (2). Install plug (2) into Position (X) in the cylinder block. Tighten the plug to a torque of 50 N m (37 lb ft). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts cone Caterpillar catalog:
120B, 12E, 12F, 140B, 14E, 611, 615, 615C, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 793B, 793C, 793D, 814F, 814F II, 834B, 834G, 834H, 834K, 836G, 836H, 836K, 938H, 941, 951B, 966F, 966F II...
120B, 12F, 140B, 14E, 24H, 589, 631C, 631E, 631G, 633C, 633E II, 637, 637D, 637E, 637G, 641, 641B, 650B, 651, 651E, 657, 657B, 657E, 657G, 666, 69D, 768C, 769, 769C, 769D, 770, 770G, 770G OEM, 771C, 7...
120, 120B, 12E, 140, 140B, 518, 518C, 528, 528B, 530B, 561B, 561C, 572G, 941, 951B, 955C, 955H, 955K, 955L, 977D, 977H, 983, D4D, D4E, D4E SR, D5, D5B, D5E, D7E, D7E LGP, D7F, D7G
120B, 12E, 12F, 140, 594, 594H, D9G, D9H
12E, 140B, 14E, 14M, 545, 545C, 545D, 555D, 814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F, R1600, R1600G, R1600H
120, 120B, 12E, 12F, 140B, 14E, D7G, D7G2
120B, 12E, 140, 140B
120, 120B, 12E, 12F, 140B, 14E
120B, 12E, 140B
120B, 12E, 140B
12E
120, 120B, 12E, 12F, 140B, 14E
120B, 12E, 140, 140B
2580070
CONE
MH3037, MH3049, MH3059
MH3037, MH3049, MH3059
345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
2197057
CONE-BEARING
CTV15
CTV15
2197060
CONE-BEARING
CTV15
CTV15
4D7951
CONE
16
16
12E
120B, 12E, 140B
120B, 12E, 140B
1B5384
CONE
16
16
14E