6V0328 CONE-ROLLER BEARING Caterpillar parts
527, 735, 735B, 740, 740B, 953C, 953D, 963C, 963D, D5H, D5H XL, D5HTSK II, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III,...
Rating:
Alternative (cross code) number:
CA6V0328
6V-0328
6V0328
CA6V0328
6V-0328
6V0328
Weight: 6 pounds 3 kg.
ARTICULATED TRUCK, TRACK-TYPE TRACTOR,
Related part:
6V0328
BEARING-YM
3994442
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 6V0328:
PIPELAYER
PL61
Information:
MID 027 CID 0177 FMI 04Conditions Which Generate This Code:
Illustration 1 g01309283
Connections of the transmission oil temperature sensor
The diagnostic code is associated with the transmission oil temperature sensor. The FMI 04 means that the ECM has determined that the voltage of the circuit for the sensor is below normal.The possible causes for this diagnostic code are listed:
The sensor supply circuit to the transmission oil temperature sensor is shorted to ground.
A sensor has failed.
The Transmission ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0177 FMI 04 is active before performing this procedure.Note: Use the digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the sensor from the machine harness. Expected Result:The CID 0177 FMI 04 remains active. The FMI has not changed and the "04" is still active.Results:
OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.
NOT OK - The diagnostic code is no longer active. The sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the sensor.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector for the ECM, measure the resistance from the signal contact J2-25 (wire 428-OR(Orange)) of the machine harness to all possible sources of ground. Measure the resistance to all contacts of the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - One or more resistance measurements is not correct. There is a short in the machine harness. The short is between signal contact J2-25 (wire 428-OR(Orange)) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 0177 FMI 04 is active. Expected Result:The CID 0177 FMI 04 is active.Results:
YES - The CID 0177 FMI 04 is active. The problem has not been corrected.Repair: Check the circuit again. If
Illustration 1 g01309283
Connections of the transmission oil temperature sensor
The diagnostic code is associated with the transmission oil temperature sensor. The FMI 04 means that the ECM has determined that the voltage of the circuit for the sensor is below normal.The possible causes for this diagnostic code are listed:
The sensor supply circuit to the transmission oil temperature sensor is shorted to ground.
A sensor has failed.
The Transmission ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0177 FMI 04 is active before performing this procedure.Note: Use the digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SENSOR
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Disconnect the sensor from the machine harness. Expected Result:The CID 0177 FMI 04 remains active. The FMI has not changed and the "04" is still active.Results:
OK - The diagnostic code remains active. The sensor is correct. Proceed to Test Step 2.
NOT OK - The diagnostic code is no longer active. The sensor has failed.Repair: Replace the sensor.STOPTest Step 2. CHECK THE WIRING HARNESS OF THE SENSOR FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the sensor.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector for the ECM, measure the resistance from the signal contact J2-25 (wire 428-OR(Orange)) of the machine harness to all possible sources of ground. Measure the resistance to all contacts of the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - One or more resistance measurements is not correct. There is a short in the machine harness. The short is between signal contact J2-25 (wire 428-OR(Orange)) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 0177 FMI 04 is active. Expected Result:The CID 0177 FMI 04 is active.Results:
YES - The CID 0177 FMI 04 is active. The problem has not been corrected.Repair: Check the circuit again. If
Cat SIS web machinery list:
Parts cone Caterpillar catalog:
9M2744
CONE-BEARING
641, 641B, 650B, 651E, 657B, 657E, 657G, 666, 735, 735B, 740, 740B, 772, 772B, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776C, 776D, 777,...
641, 641B, 650B, 651E, 657B, 657E, 657G, 666, 735, 735B, 740, 740B, 772, 772B, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776C, 776D, 777,...
5P9533
CONE-BEARING
613, 920, D4H, D5H
613, 920, D4H, D5H
2054138
CONE-BEARING
527, D5H XL, D6M, D6N
527, D5H XL, D6M, D6N
1119033
CONE-BEARING
953C, 963C, 973D
953C, 963C, 973D
2K5066
CONE-BEARING
508, 518, 528, 613, 613B, 613C, 613C II, 613G, 615, 725, 725C, 730, 814, 814B, 815, 815B, 816B, 936, 950, 950B/950E, 966C, 966D, D250B, D250E, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D35C, D35HP...
508, 518, 528, 613, 613B, 613C, 613C II, 613G, 615, 725, 725C, 730, 814, 814B, 815, 815B, 816B, 936, 950, 950B/950E, 966C, 966D, D250B, D250E, D25C, D25D, D300B, D300D, D300E, D30C, D350C, D35C, D35HP...
8H0902
CONE-BEARING
583H, 583K, 824C, 953, 953B, 980, 980B, 980C, 980F, 980F II, 994, 994D, 994F, 994H, AD40, AE40, D35C, D40D, D44B, D550B, D6T LGP, D8H, D8K, R1700 II, TS180, TS185, TS220, TS225
583H, 583K, 824C, 953, 953B, 980, 980B, 980C, 980F, 980F II, 994, 994D, 994F, 994H, AD40, AE40, D35C, D40D, D44B, D550B, D6T LGP, D8H, D8K, R1700 II, TS180, TS185, TS220, TS225
6V2449
CONE
12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 518, 518C, D4HTSK II, D4HTSK III, D5HTSK II, D9H
12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 518, 518C, D4HTSK II, D4HTSK III, D5HTSK II, D9H
5P7605
CONE-ROLLER BEARING
518, 527, 931B, D5C, D5HTSK II
518, 527, 931B, D5C, D5HTSK II
2D9455
CONE-BEARING
12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 2470C, 2570C, 2670C, 2864C, 518, 525B, 525C, 525D, 528, 528B, 530B, 533, 535B, ...
12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16H NA, 2470C, 2570C, 2670C, 2864C, 518, 525B, 525C, 525D, 528, 528B, 530B, 533, 535B, ...
6V3950
CONE-BEARING
613C, 725, 725C, 730, 730C, 735, 918F, 924F, 924G, 924GZ, 924H, 924HZ, D250E II, D300E II, D350E II, IT18F, IT24F
613C, 725, 725C, 730, 730C, 735, 918F, 924F, 924G, 924GZ, 924H, 924HZ, D250E II, D300E II, D350E II, IT18F, IT24F
2P1824
CONE-BEARING
621, 621B, 621E, 621F, 621G, 621H, 621K, 623, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 735B, 740B, 824B, 825B, 825C, 826B, 826C, 988, 992C, D10, D11N,...
621, 621B, 621E, 621F, 621G, 621H, 621K, 623, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 735B, 740B, 824B, 825B, 825C, 826B, 826C, 988, 992C, D10, D11N,...
1P4694
CONE-BEARING
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 725, 725C, 730, 730C, 735, 777, 844, 84...
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 725, 725C, 730, 730C, 735, 777, 844, 84...
1B3980
CONE-ROLLER BEARING
518, 518C, 527, 528, 528B, 530B, 589, 631D, 631E, 631G, 633E, 637D, 637E, 637G, 639D, 657, 657B, 666, 910, 910E, 916, 918F, 920, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 928HZ, 930, 930G, 930...
518, 518C, 527, 528, 528B, 530B, 589, 631D, 631E, 631G, 633E, 637D, 637E, 637G, 639D, 657, 657B, 666, 910, 910E, 916, 918F, 920, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928G, 928H, 928HZ, 930, 930G, 930...
5W5817
CONE
205, 206, 212
205, 206, 212
8U0589
CONE-VALVE
206, 206B, 212, 212B, 214B, 224B
206, 206B, 212, 212B, 214B, 224B
8U0600
CONE-VALVE
206, 206B, 212, 212B, 214B, 224B
206, 206B, 212, 212B, 214B, 224B
8R8783
CONE-ROLLER BEARING
225D, 229
225D, 229
9W3620
CONE-BEARING
245D, 375, 375 L, 5080, 578, 583R, 587R, 589, D4H, D4HTSK II, D8N, D8R, D8R II, D9N
245D, 375, 375 L, 5080, 578, 583R, 587R, 589, D4H, D4HTSK II, D8N, D8R, D8R II, D9N
8T0072
CONE-ROLLER BEARING
517, 561M, 561N, 583T, 615C, 933C, 939C, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4H, D4H XL, D4HTSK II, D4HTSK III, D4K XL, D4K2 XL, D5C III, D5G, D5K LGP, D5K2 XL, D5M, D5N, D5R LGP, D6N, D6N ...
517, 561M, 561N, 583T, 615C, 933C, 939C, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4H, D4H XL, D4HTSK II, D4HTSK III, D4K XL, D4K2 XL, D5C III, D5G, D5K LGP, D5K2 XL, D5M, D5N, D5R LGP, D6N, D6N ...
7T8288
CONE
973
973
5F0585
CONE-BEARING
16, 621, 623, 627, 630A, 630B, 631B, 631D, 631E, 631G, 637, 637B, 637D, 637E, 637G, 641B, 651, 651B, 651E, 657, 657B, 657E, 657G, 666, 953D, 963D, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
16, 621, 623, 627, 630A, 630B, 631B, 631D, 631E, 631G, 637, 637B, 637D, 637E, 637G, 641B, 651, 651B, 651E, 657, 657B, 657E, 657G, 666, 953D, 963D, D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
2850586
CONE
953D, 963D
953D, 963D
1564593
CONE-BEARING
D10R, D6H, D6H XL, D6R, D6R II, D6R III, D6T
D10R, D6H, D6H XL, D6R, D6R II, D6R III, D6T
6V0329
CONE-ROLLER BEARING
527, D5H, D5H XL, D5HTSK II, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL
527, D5H, D5H XL, D5HTSK II, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6M, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL