3335465 CONNECTING ROD GP Caterpillar parts
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ100, C4.4XQ80, CB-44B, CB-54B, CP-54B, CP-68B, CP-74B, CS-54B, CS-56B, CS-64B, CS-66B, CS-7...
Rating:
Alternative (cross code) number:
CA3335465
333-5465
3335465
CA3335465
333-5465
3335465
Weight: 4 pounds 2 kg.
BACKHOE LOADER, VIBRATORY COMPACTOR,
Number on catalog scheme:
2
For full view, you need register
Information:
This diagnostic trouble code is recorded when the software location code for the Power Train ECM does not match the hardware location codes.The probable cause of this diagnostic trouble code is software. The wrong software has been flashed into the ECM.Note: Do not change the hard wired location code if you have flashed the incorrect software into the control.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1326 FMI 02 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. VERIFY THE HARDWARE AND SOFTWARE PART NUMBERS.
Verify whether the part number of the software for the ECM is correct. Expected Result:Consult the Business Unit that is producing the product for the correct configuration for the machine.Results:
OK - All part numbers are correct for the ECM. Proceed to test step 2.
NOT OK - All part numbers are not correct. The installed ECM has the wrong part number or incorrect configuration software is installed.Repair: Replace the ECM with a module that has the correct part number or flash the correct configuration software. See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. VERIFY THAT THE LOCATION CODE MATCHES THE STATUS SCREEN OF THE CATERPILLAR ELECTRONIC TECHNICIAN.
Check the status screen of the Caterpillar Electronic Technician (Cat ET) in order to verify the location code . Expected Result:The location codes in the Cat ET are correct.Results:
OK - The location codes in the Cat ET are correct. Proceed to test step 3.
NOT OK - The location codes are not correct. Repair: Repeat this test step in order to verify that the software and hardware part numbers are correct. Proceed to test step 3 if the part numbers are correct.Test Step 3. INSPECT THE HARNESS CONNECTIONS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing. Make sure that the connectors are tight.
Check for the proper mating of the connector.
Check all wires at the connector.
Check for moisture at the connector.
Check for dirty contacts or corroded contacts.
Check each pin and check each socket. Expected Result:The machine harness connectors are tight and the machine harness connectors are free of corrosion.Results:
OK - The machine harness connectors are tight and the machine harness connectors are free from corrosion. Proceed to test step 4.
NOT OK - One or
Verify whether the part number of the software for the ECM is correct. Expected Result:Consult the Business Unit that is producing the product for the correct configuration for the machine.Results:
OK - All part numbers are correct for the ECM. Proceed to test step 2.
NOT OK - All part numbers are not correct. The installed ECM has the wrong part number or incorrect configuration software is installed.Repair: Replace the ECM with a module that has the correct part number or flash the correct configuration software. See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program".STOPTest Step 2. VERIFY THAT THE LOCATION CODE MATCHES THE STATUS SCREEN OF THE CATERPILLAR ELECTRONIC TECHNICIAN.
Check the status screen of the Caterpillar Electronic Technician (Cat ET) in order to verify the location code . Expected Result:The location codes in the Cat ET are correct.Results:
OK - The location codes in the Cat ET are correct. Proceed to test step 3.
NOT OK - The location codes are not correct. Repair: Repeat this test step in order to verify that the software and hardware part numbers are correct. Proceed to test step 3 if the part numbers are correct.Test Step 3. INSPECT THE HARNESS CONNECTIONS.
Turn the key start switch and the disconnect switch to the OFF position.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing. Make sure that the connectors are tight.
Check for the proper mating of the connector.
Check all wires at the connector.
Check for moisture at the connector.
Check for dirty contacts or corroded contacts.
Check each pin and check each socket. Expected Result:The machine harness connectors are tight and the machine harness connectors are free of corrosion.Results:
OK - The machine harness connectors are tight and the machine harness connectors are free from corrosion. Proceed to test step 4.
NOT OK - One or
Cat SIS web machinery list:
Parts connecting Caterpillar catalog:
120M, 120M 2, 12M, 2384C, 2470C, 2484C, 2570C, 2670C, 320D GC, 320D L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 553C, 5...
9N2142
CONNECTING ROD AND PISTON GROUP
1140, 1145, 3145
1140, 1145, 3145
9L8569
CONNECTING ROD AND PISTON GROUP
1140, 1145, 3145
1140, 1145, 3145
4M2708
CONNECTING ROD AND PISTON GROUP
641, 651, 657
641, 651, 657
5S9564
CONNECTING ROD
215, 772, D4D
215, 772, D4D
1609786
CONNECTING AS-FLEXIBLE
G3612, G3616
G3612, G3616
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 559, 613G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, BG600D, BG655D, C6.6, CP-56, CP-64, CP-76, CS-56, CS-56B, CS...
120M, 120M 2, 12M, 2384C, 2470C, 2484C, 2570C, 2670C, 320D GC, 320D L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323D L, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 525D, 535D, 545D, 553C, 5...