AVSPARE.COM
parts catalog

CONNECTOR GP-CAB HEATER LINES 3236240 - Caterpillar



3236240 CONNECTOR GP-CAB HEATER LINES Caterpillar parts C4.4 CONNECTOR
Rating:
22
Alternative (cross code) number:
CA3236240
323-6240
3236240
Caterpillar 3236240 CONNECTOR GP-CAB HEATER LINES

Buy CONNECTOR GP-CAB HEATER LINES 3236240 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE,

Compatible equipment models: 3236240:

INDUSTRIAL ENGINE  C4.4   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Disconnect governor cable (F) from governor lever assembly (12) .
Remove the seven bolts that secure case (10) to the back plate. Remove the case.
Turn over the case. The governor spring (9) and associated parts will be visible. Remove the former governor spring and install a new governor spring. The new governor spring will be much stiffer. Move the case assembly to one side.
Carefully remove shaft assembly (5). Refer to Illustration 1.
Illustration 6 g01380623
Disassembly Of The Governor Weight Assembly
Remove the three bolts that secure weight assembly (4) .
Illustration 7 g01380629
Weight Assembly (4) 259-8502 Weight As (G) PinNote: The weight assembly in Illustration 7 shows the weight assembly on the gear.
Carefully cut pin (G) from the weight assembly. If the surface of the pin is worn, shaft assembly (5) will not slide smoothly. The function of the pin is for preventing shaft assembly (5) from turning. The system will operate satisfactorily without the pin. The pin is not needed. It is not necessary for the cut of the pin to be flush with the base plate. If part of the pin remains, make sure that the part does not engage with the hole in the shaft assembly. Make sure that the cut surface on the pin is free from burrs and thoroughly cleaned.
Remove all of the former gasket from case (10) and the back plate. Make sure that the former gasket is completely removed. Make sure that the fragments of the former gasket are not located between the gear teeth or behind the gears.
Install the modified weight assembly. Tighten the three bolts evenly to a torque of 18.7 4 N m (14 3 lb ft).
Install the shaft assembly.
Smear the back side of the new 246-3077 Gasket and the surface of the case with 185-3985 Gasket Sealant . Install the gasket and the case. Tighten the seven bolts evenly to a torque of 18.7 4 N m (14 3 lb ft).
Install crankshaft pulley (C). Tighten the nut to a torque of 220 25 N m (162 18 lb ft). Use two threaded studs (E) and bar (D) to hold the crankshaft while you tighten the nut.
Illustration 8 g01380630
Cover Assembly (H) 253-5566 Cover As
If the 253-5566 Cover As was previously installed, remove cover assembly (H). Replace the cover assembly with a new oil filler (7) and a new cap assembly (6). Use a new gasket (8). The 253-5566 Cover As could remain on the engine. The cover assembly has the disadvantage of not having the cap assembly. Installation of a new 253-9180 Oil Filler allows the engine oil level to be maintained through the cap assembly. The recommendation is for the installation of the 253-9180 Oil Filler in order to allow the engine oil level to be maintained through the cap assembly. If the 253-5566 Cover As is reused, the oil level can be maintained through an alternative filler cap on the top of the engine. The alternative filler

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
C4.4 Industrial Engine 44400001-UP


Parts connector Caterpillar catalog:

9M6522 CONNECTOR
12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 16H NA, 245B, 3126B, 3126E, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 3406B, 3406...
1224371 CONNECTOR-PLUG
35, 45, 55, C2.2, C4.4, C6.6, C7.1
1282312 CONNECTOR
3306B, 3406C, 35, 45, 55, C1.5, C15, C15 I6, C18, C18 I6, C2.2, C3.3, C4.4, C6.6, C7.1, C9, G3406
2950189 CONNECTOR AS
420E, 430E, 450E, 924H, 924HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP555E, C4.4, CP-44, CS-44, CS-54, CS-54B, CW-34, D6K LGP, D6N, IT38H, M313D, M315D, M316D, M317D 2, M318D, M318D MH, M322D, M322D MH...
0619463 CONNECTOR
215, 215B, 225, 229D, 245, 245B, 3306C, 3406, 3406C, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3612, 3616, 527, 528, 561M, 583K, 611, 613B, 613C II, 615, 615C, 627B, 637D, 777B, 785,...
3R5387 CONNECTOR
140B, 140G, 14G, 1673C, 235, 3114, 3116, 3126, 3208, 3304, 3306, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3456, 3508B, 3508C, 3512, 3516B, 3608, 3612, 3616, 3618, 530B, 589, 611, 6...
2620502 CONNECTOR
C1.5, C2.2, C3.3, C4.4, C6.6
2609255 CONNECTOR
C3.3, C4.4, C6.6
3381539 CONNECTOR
C4.4, C6.6, C7.1
6D2784 CONNECTOR
14E, 16, 589, 621, 623, 627, 633C, 768B, 769, 769C, 772, 773, 773B, 776C, 776D, 777B, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, C4.4, C6.6, D8L
2159515 CONNECTOR-HOSE
120M, 12M, 2384C, 2484C, 3054C, 3054E, 315C, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 559C,...
2159513 CONNECTOR-HOSE
2384C, 2484C, 3054C, 3054E, 315C, 416E, 416F, 420F, 422F, 428F, 430F, 432F, 434F, 444F, 559C, 579C, 914G, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B, CP-56, CP-64, CP-76, CS-54B, CS-56, CS-56B...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.