CONSOLE 0792040 - Caterpillar

Install Grommet (11) over Cylinder (AK). Make sure that the "U" cutout on Grommet (11) sits over the upper fitting of Cylinder (AK). Refer to Illustration 60.
Illustration 61 g06068790
Arrow indicates snaps
(12) 458-6064 Boot
(21) 471-9968 Support As
(22) 476-7386 Support As
(24) 476-7388 Bracket
(26) 476-7390 Plate
Install Boot assembly (12) on to raised lips of Bracket (24) and Plate (26). Refer to Illustration 61.
Illustration 62 g06068795
(9) 444-9532 Plate
(10) 444-9533 Plate
(12) 458-6064 Boot
(42) 6V-7743 Locknut
(48) 8T-4205 Hard Washer
Secure bottom flap of Boot assembly (12) against Support As (21) using two Plates (9), Plate (10), eight Locknuts (42), and Hard Washer (48). Torque nut to 6 1 N m (53 9 lb in). Refer to Illustration 61.Note: Ensure Boot assembly (12) is placed so that Snaps of Boot assembly (12) are facing machine
Illustration 63 g06068796
(6) 323-3309 Cap
(11) 444-9680 Grommet
(12) 458-6064 Boot
(50) 8T-6726 Hose Clamp
Button the snaps of Boot Assembly (12). Clamp the top of Boot assembly (12) as low as possible with Grommet (11) using Hose Clamp (50) and Cap (6). Refer Illustration 63.
Illustration 64 g06068802
(10) 444-9533 Plate
(12) 458-6064 Boot
(22) 476-7386 Support As
(31) 113-8694 Bolt
Secure Boot assembly (12) with Plate (10) aligning on the weld nuts to Support As (22) and using two Bolts (31). Torque bolts (31) to 6 1 N m (53 9 lb in). Refer to Illustration 64.Installing Protection for the Right side Lift Cylinder
Illustration 65 g06068808
Arrow indicates snaps
(12) 458-6064 Boot
(20) 471-9967 Support As
(23) 476-7387 Support As
(25) 476-7389 Bracket
(26) 476-7390 Plate
(37) 343-4072 Bolt
Illustration 66 g06068810
(6) 323-3309 Cap
(11) 444-9680 Grommet
(12) 458-6064 Boot
(50) 8T-6726 Hose ClampFollow the same procedure as instructed in "Installing Protection for the Left side lift Cylinder" to install protection for the Right side lift cylinder. Use Support As (23), Support As (20), Bracket (25), Plate (26), Boot As (12), Grommet (11) , Hose Clamp (50), Cap (6), two Plates (9), two Plates (10), eight Lock Nuts (42) and eight Washers (48), Insulation (7)), six Bolts (31), and five Bolts (37).Note:Ensure Snaps of Boot Assembly (12) are facing away from machine. Refer Illustrations 65 and 66.Installing Fuel Strainer on the Fuel Fill adapter
Illustration 67 g06068813
(AL) Fuel Cap
(AM) Fuel Tank
(4) 282-2270 Fuel Strainer
Remove the Fuel Cap (AL) from the Fuel Tank (AM)
Install Fuel Strainer (4) inside the fuel fill neck of the tank.
Ensure Fuel Strainer (4) fits into the adapter mouth of the fuel fill area and then put back the Fuel Cap (AL). Refer to Illustration 67.