2405309 CONT GP Caterpillar parts
Rating:
Alternative (cross code) number:
CA2405309
240-5309
2405309
CA2405309
240-5309
2405309
Weight: 5 pounds 2 kg.
Related part:
2405309
CONT GP -E
10R8142
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
240-5309 10R8142 Controller ECU for Caterpillar Engine
monica Part Number:240-5309 || Application: for Caterpillar Engine || ✅Warm Tips:This product is related to the correctness of the programme, please send us the following information: Loader Nameplate, Engine Nameplate, Part Number. || SAVE FUEL:By optimizing engine operating parameters, precise control of fuel injection and ignition is achieved, thereby improving fuel economy and reducing fuel consumption. || FAULT DIAGNOSIS AND MAINTENANCE:It can detect problems in the vehicle system and provide guidance through fault codes to facilitate maintenance personnel to quickly locate and solve problems.
monica Part Number:240-5309 || Application: for Caterpillar Engine || ✅Warm Tips:This product is related to the correctness of the programme, please send us the following information: Loader Nameplate, Engine Nameplate, Part Number. || SAVE FUEL:By optimizing engine operating parameters, precise control of fuel injection and ignition is achieved, thereby improving fuel economy and reducing fuel consumption. || FAULT DIAGNOSIS AND MAINTENANCE:It can detect problems in the vehicle system and provide guidance through fault codes to facilitate maintenance personnel to quickly locate and solve problems.
240-5313 240-5309 C9 Compatible For CAT ECU Electronic Control Unit Controller Compatible For E330C Excavator With Programs(240-5309)
JTWABK Can supervise engine operation || Good product quality and long usage time || Adjust vehicle performance such as idle and boost || Diagnosis of faults, safety protection, and emergency response || 240-5313 240-5309 C9 Compatible For CAT ECU Electronic Control Unit Controller Compatible For E330C Excavator With Programs
JTWABK Can supervise engine operation || Good product quality and long usage time || Adjust vehicle performance such as idle and boost || Diagnosis of faults, safety protection, and emergency response || 240-5313 240-5309 C9 Compatible For CAT ECU Electronic Control Unit Controller Compatible For E330C Excavator With Programs
240-5309 2405309 Engine Computer Boards for Cat ECU Electronic Control Unit with Programs
Seodon Model Name：2405309 || The functions of the diesel ECU 2405309 computer board mainly include engine performance control, fuel efficiency management, emission control, fault diagnosis, safety functions, and driving mode adjustment. || Purchase Note: Due to different machine models and different programs, please make sure that the product you need to buy has the same appearance and model as ours. If you are not sure, you can consult us before purchase, we will match the right product for you. || ECU is a blank ecu without data before shipment, if you need us to program it, please provide the machine's ECU number and a picture of the body nameplate. We will make sure the data is ok and program it for you before shipping. This will save your valuable time, thanks. || Direct replacement: Plug and play, easy to install, you can use directly. testing before shipment to ensure product safety, stability and durability. || Service: We provide technical support; if you receive the product use problems, you can contact customer service to solve the problem, we will reply you within 24 hours, thank you!
Seodon Model Name：2405309 || The functions of the diesel ECU 2405309 computer board mainly include engine performance control, fuel efficiency management, emission control, fault diagnosis, safety functions, and driving mode adjustment. || Purchase Note: Due to different machine models and different programs, please make sure that the product you need to buy has the same appearance and model as ours. If you are not sure, you can consult us before purchase, we will match the right product for you. || ECU is a blank ecu without data before shipment, if you need us to program it, please provide the machine's ECU number and a picture of the body nameplate. We will make sure the data is ok and program it for you before shipping. This will save your valuable time, thanks. || Direct replacement: Plug and play, easy to install, you can use directly. testing before shipment to ensure product safety, stability and durability. || Service: We provide technical support; if you receive the product use problems, you can contact customer service to solve the problem, we will reply you within 24 hours, thank you!
For full view, you need register
Information:
Note: When Tooling (B) is removed be careful to prevent contamination. Cleanliness is an important factor. Before assembly, clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
Illustration 1 g02149623
Illustration 2 g06151585Note: Reuse dowel components after cleaning using clean solvent.
Do not use dowels that have been completely removed from the block. Use a dead blow hammer to install new dowel assembly in block. Install new dowel assembly by lightly tapping the dowel until the dowel assembly is flush with the block surface. Excessive force can damage the dowel or block. Refer to illustration 2. If only the top part of the dowel has been removed, Use a screwdriver to install the dowel and apply a torque of 2 N m (18 lb in).Remove the O-ring seals from dowel assembly (14). Clean and inspect the O-ring seals. If necessary, replace the O-ring seals with new O-ring seals. Remove Tooling (B) and clean oil supply hole. Install dowel assembly (14).Note: Important to replace fire ring with new fire ring.
Replace fire ring (15) with new fire ring (15). Install fire ring (15). Install a new gasket (13) onto the cylinder block.
Illustration 3 g06151438Note: Clean the bottom surface of the cylinder head and the top surface of the cylinder block.
Attach Tooling (A) and a suitable lifting device onto cylinder head (3). The weight of cylinder head (3) is approximately 68 kg (150 lb). Position cylinder head (3) onto the cylinder block.
Illustration 4 g06151461
Illustration 5 g06151463Note: Ensure that the sleeve is installed with the chamfer facing downward. The sleeve must be flush with the top of the cylinder head surface.
Install sleeves (16) in cylinder head (3). Sleeves (16) are installed in the two bolt holes as shown in illustration 4.
Illustration 6 g06151466
Illustration 7 g02161103
Lubricate the threads of bolts (4) with oil. Install bolts (4). Hand tighten all bolts (4) in the numerical sequence to a maximum torque of 15 N m (11 lb ft). Use Tooling (D) to tighten bolts (4) in the numerical sequence to a torque of 100 10 N m (75 7 lb ft). Tighten bolts (4) again in the numerical sequence to a torque of 250 15 N m (185 11 lb ft). Tighten bolts (4) in the numerical sequence for an additional 180 5 degrees.
Install the unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Illustration 8 g02090762
Illustration 9 g01285695
Apply clean engine oil to area (X). Repeat for the opposite collar. Apply Tooling (C) to the ends of tube assembly (6). Install tube assembly (6). Replace external O-ring seals on tube assembly (6) and lubricate the O-ring seals on the tube assembly with clean engine oil. Install
Illustration 1 g02149623
Illustration 2 g06151585Note: Reuse dowel components after cleaning using clean solvent.
Do not use dowels that have been completely removed from the block. Use a dead blow hammer to install new dowel assembly in block. Install new dowel assembly by lightly tapping the dowel until the dowel assembly is flush with the block surface. Excessive force can damage the dowel or block. Refer to illustration 2. If only the top part of the dowel has been removed, Use a screwdriver to install the dowel and apply a torque of 2 N m (18 lb in).Remove the O-ring seals from dowel assembly (14). Clean and inspect the O-ring seals. If necessary, replace the O-ring seals with new O-ring seals. Remove Tooling (B) and clean oil supply hole. Install dowel assembly (14).Note: Important to replace fire ring with new fire ring.
Replace fire ring (15) with new fire ring (15). Install fire ring (15). Install a new gasket (13) onto the cylinder block.
Illustration 3 g06151438Note: Clean the bottom surface of the cylinder head and the top surface of the cylinder block.
Attach Tooling (A) and a suitable lifting device onto cylinder head (3). The weight of cylinder head (3) is approximately 68 kg (150 lb). Position cylinder head (3) onto the cylinder block.
Illustration 4 g06151461
Illustration 5 g06151463Note: Ensure that the sleeve is installed with the chamfer facing downward. The sleeve must be flush with the top of the cylinder head surface.
Install sleeves (16) in cylinder head (3). Sleeves (16) are installed in the two bolt holes as shown in illustration 4.
Illustration 6 g06151466
Illustration 7 g02161103
Lubricate the threads of bolts (4) with oil. Install bolts (4). Hand tighten all bolts (4) in the numerical sequence to a maximum torque of 15 N m (11 lb ft). Use Tooling (D) to tighten bolts (4) in the numerical sequence to a torque of 100 10 N m (75 7 lb ft). Tighten bolts (4) again in the numerical sequence to a torque of 250 15 N m (185 11 lb ft). Tighten bolts (4) in the numerical sequence for an additional 180 5 degrees.
Install the unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Illustration 8 g02090762
Illustration 9 g01285695
Apply clean engine oil to area (X). Repeat for the opposite collar. Apply Tooling (C) to the ends of tube assembly (6). Install tube assembly (6). Replace external O-ring seals on tube assembly (6) and lubricate the O-ring seals on the tube assembly with clean engine oil. Install
Parts cont Caterpillar catalog:
2401012
CONT GP-
Caterpillar
Caterpillar
2400835
CONT GP-BUCKET
Caterpillar
Caterpillar
2399216
CONT GP
Caterpillar
Caterpillar
2398443
CONT GP
Caterpillar
Caterpillar
2398391
CONT GP
Caterpillar
Caterpillar
2398054
CONT GP
Caterpillar
Caterpillar
2428289
CONT GP-
Caterpillar
Caterpillar
2428281
CONT GP-
Caterpillar
Caterpillar
2421264
CONT GP
Caterpillar
Caterpillar
Caterpillar
2405316
CONT GP
Caterpillar
Caterpillar
2405311
CONT GP
Caterpillar
Caterpillar