5110170 CONT GP Caterpillar parts
Rating:
Alternative (cross code) number:
CA5110170
511-0170
5110170
CA5110170
511-0170
5110170
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$20.00
15 Jun 2021
US: Walter A. Wood
Union Butterfield 5110170 High Speed Steel (HSS) Square Nose End Mill, Inch, Double End, Weldon Shank, Uncoated (Bright) Finish, 4 Flutes, 6.125" Overall Length, 7/8" Cutting Diameter, 7/8" Shank Diameter
Union Butterfield Four flutes produce a better finish than fewer flutes || High-speed steel is compatible with a variety of materials || Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials || Double-end square end mills create sharp, unrounded cuts and have cutting edges on both ends for longer tool life || Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling
Union Butterfield Four flutes produce a better finish than fewer flutes || High-speed steel is compatible with a variety of materials || Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials || Double-end square end mills create sharp, unrounded cuts and have cutting edges on both ends for longer tool life || Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
Illustration 1 g01116830
Note: Removal of guard (2) is optional for clearance purposes.
Install Tooling (A) under guard (2). Remove bolts (1). Repeat for the other side. Use Tooling (A) to lower guard (2) to the ground. The weight of guard (2) is approximately 38 kg (85 lb).
Illustration 2 g01116832
Remove bolts (3). Discard bolts (3) .
Illustration 3 g01116843
Remove bolts (5) and front drive shaft (4). Discard bolts (5) .Installation Procedure
Install front drive shaft (4) in the reverse order of removal.
Use new bolts for bolts (3) and bolts (5) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
Illustration 1 g01116830
Note: Removal of guard (2) is optional for clearance purposes.
Install Tooling (A) under guard (2). Remove bolts (1). Repeat for the other side. Use Tooling (A) to lower guard (2) to the ground. The weight of guard (2) is approximately 38 kg (85 lb).
Illustration 2 g01116832
Remove bolts (3). Discard bolts (3) .
Illustration 3 g01116843
Remove bolts (5) and front drive shaft (4). Discard bolts (5) .Installation Procedure
Install front drive shaft (4) in the reverse order of removal.
Use new bolts for bolts (3) and bolts (5) .
Parts cont Caterpillar catalog:
5110169
CONT GP
Caterpillar
Caterpillar
5110168
CONT GP
Caterpillar
Caterpillar
5110167
CONT GP
Caterpillar
Caterpillar
5109937
CONT GP-
Caterpillar
Caterpillar
5104068
CONT GP
Caterpillar
Caterpillar
5086698
CONT GP
Caterpillar
Caterpillar
5126360
CONT GP-HEAD
Caterpillar
Caterpillar
5123167
CONT GP
Caterpillar
Caterpillar
5122636
CONT GP-MTG& -
Caterpillar
Caterpillar
5117692
CONT GP-COM
Caterpillar
Caterpillar
5115894
CONT AS-JOYSTI
Caterpillar
Caterpillar
5110798
CONT GP-EH
Caterpillar
Caterpillar