1020258 CONTROL GP-STEERING Caterpillar parts
CB-434B, CB-534B, CB-634
Rating:
Alternative (cross code) number:
CA1020258
102-0258
1020258
CA1020258
102-0258
1020258
VIBRATORY COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Qpmalsns 1pc Radiator 1 Row with Automatic Transmission Automotive 102-0258
Qpmalsns Fitment:Please check Amazon Fitment Filter and Description to see if this item_temp will work on your vehicle before purchase! || Part_Number:CU13231,102-0258 || Feature_1: 100% test before leaving the factory || Feature_2: Matching Quality Designed,manufactured and thoroughly tested according to requirements || Condition: 100% New in original factory packaging, never used or installed. Pristine condition ensures quality and performance of the product.
Qpmalsns Fitment:Please check Amazon Fitment Filter and Description to see if this item_temp will work on your vehicle before purchase! || Part_Number:CU13231,102-0258 || Feature_1: 100% test before leaving the factory || Feature_2: Matching Quality Designed,manufactured and thoroughly tested according to requirements || Condition: 100% New in original factory packaging, never used or installed. Pristine condition ensures quality and performance of the product.
Number on catalog scheme:
For full view, you need register
Information:
Introduction
This Special Instruction gives the information that is required in order to install the 230-1394 Shock Absorber Kit (Extreme Duty). Use this kit if the surface conditions do not permit the proper operation of the suspension. This kit is also used if the weight of the operators exceeds 136 kg (300 lb).The shock absorber from the kit is installed in addition to the existing adjustable shock absorber. The boot is removed from the suspension, and the auxiliary shock absorber is installed. The auxiliary shock absorber will prevent undesired contact with the stops for the suspension. Required Parts
Illustration 1 g00937125
A view of the seat suspension without boot (3) and without top plate assembly. (4) Cable straps (5) Existing adjustable shock absorber (6A) Location for new shock absorber
Table 1
Ref No Qty Part Number Description
6 1 230-1510 Shock Absorber
7 1 186-5114 Bearing
8 2 186-5111 Spacer
9 1 186-5112 Bearing
10 2 186-5110 Shoulder Bolt
11 2 4D-1326 Lockwasher
12 2 2K-4973 Locknut
13 2 8L-8413 Cable Strap Installation procedure
Illustration 2 g00936102
Remove one acorn nut (1). Remove 31 fasteners (2). Remove boot (3) from the suspension.
Remove two cable straps (4) that secure the harness assembly to the scissors assembly. The straps are between the upper shock mounts.
Install bearing (7) in the lower shock mount.
Orient the shock properly. Shock absorber (6) must be oriented in the same direction as shock absorber (5). All the mounting hardware for shock absorber (6) will be oriented in the opposite direction as the mounting hardware for shock absorber (5) .
Hold the shock in assembly position (6A).
Install spacer (8) on the open side between the lower shock mount and the bracket on the scissor assembly.
Insert one bolt (10) with the threads toward the outboard side. Note: Bolt (10) is oriented in the opposite direction from the same bolt on the adjustable shock absorber (5) .
Install lockwasher (11) and locknut (12). Tighten the locknut finger tight.
Install bearing (9) and spacer (8) on the upper end of shock absorber (6) .
Tilt shock absorber (6) until the upper end and the spacers are between the brackets on the scissor assembly.
Insert one bolt (10) with the threads toward the inboard side. Note: Bolt (10) is oriented in the opposite direction from the same bolt on the adjustable shock absorber (5) .
Install lockwasher (11) and locknut (12). Tighten the locknut finger tight.
Tighten two bolts (10) to standard torque.
Rotate the electrical connector clockwise until the connector aligns with the cross-tube on the scissor assembly.
Secure the connector to the scissor assembly with two cable straps (13). Use one strap at each end of the connector approximately 12.7 mm (0.50 inch) away from the connector on the wire.
Install boot (3). Install 31 fasteners (2). Install one acorn nut (1).
This Special Instruction gives the information that is required in order to install the 230-1394 Shock Absorber Kit (Extreme Duty). Use this kit if the surface conditions do not permit the proper operation of the suspension. This kit is also used if the weight of the operators exceeds 136 kg (300 lb).The shock absorber from the kit is installed in addition to the existing adjustable shock absorber. The boot is removed from the suspension, and the auxiliary shock absorber is installed. The auxiliary shock absorber will prevent undesired contact with the stops for the suspension. Required Parts
Illustration 1 g00937125
A view of the seat suspension without boot (3) and without top plate assembly. (4) Cable straps (5) Existing adjustable shock absorber (6A) Location for new shock absorber
Table 1
Ref No Qty Part Number Description
6 1 230-1510 Shock Absorber
7 1 186-5114 Bearing
8 2 186-5111 Spacer
9 1 186-5112 Bearing
10 2 186-5110 Shoulder Bolt
11 2 4D-1326 Lockwasher
12 2 2K-4973 Locknut
13 2 8L-8413 Cable Strap Installation procedure
Illustration 2 g00936102
Remove one acorn nut (1). Remove 31 fasteners (2). Remove boot (3) from the suspension.
Remove two cable straps (4) that secure the harness assembly to the scissors assembly. The straps are between the upper shock mounts.
Install bearing (7) in the lower shock mount.
Orient the shock properly. Shock absorber (6) must be oriented in the same direction as shock absorber (5). All the mounting hardware for shock absorber (6) will be oriented in the opposite direction as the mounting hardware for shock absorber (5) .
Hold the shock in assembly position (6A).
Install spacer (8) on the open side between the lower shock mount and the bracket on the scissor assembly.
Insert one bolt (10) with the threads toward the outboard side. Note: Bolt (10) is oriented in the opposite direction from the same bolt on the adjustable shock absorber (5) .
Install lockwasher (11) and locknut (12). Tighten the locknut finger tight.
Install bearing (9) and spacer (8) on the upper end of shock absorber (6) .
Tilt shock absorber (6) until the upper end and the spacers are between the brackets on the scissor assembly.
Insert one bolt (10) with the threads toward the inboard side. Note: Bolt (10) is oriented in the opposite direction from the same bolt on the adjustable shock absorber (5) .
Install lockwasher (11) and locknut (12). Tighten the locknut finger tight.
Tighten two bolts (10) to standard torque.
Rotate the electrical connector clockwise until the connector aligns with the cross-tube on the scissor assembly.
Secure the connector to the scissor assembly with two cable straps (13). Use one strap at each end of the connector approximately 12.7 mm (0.50 inch) away from the connector on the wire.
Install boot (3). Install 31 fasteners (2). Install one acorn nut (1).
Caterpillar SIS machinery equipment:
Caterpillar SIS
CB-634 VIBRATORY COMPACTOR 5CL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
102-0258
CONTROL GP-STEERING
CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE »
102-0258
CONTROL GP-STEERING
CB-534B VIBRATORY COMPACTOR 4JL00001-UP (MACHINE) POWERED BY 3054 ENGINE »
102-0258
CONTROL GP-STEERING
CB-434B Vibratory Compactor 6AL00001-00087 (MACHINE) POWERED BY 3054 Engine »
102-0258
CONTROL GP-STEERING
Caterpillar parts catalog:
Parts control Caterpillar catalog:
6J3117
CONTROL VALVE GROUP
153, 163
153, 163
2242793
CONTROL & MTG GP-PEDAL
572R II, 587T, D6R III, D6T, D7R II
572R II, 587T, D6R III, D6T, D7R II
2012522
CONTROL GP-BLADE
CP-433C, CS-323C, CS-433C
CP-433C, CS-323C, CS-433C
2067520
CONTROL GP-HANDLE
950G, 962G, 966G, 972G, IT62G
950G, 962G, 966G, 972G, IT62G
8R8078
CONTROL GP-HYDRAULIC HAND
215D, 219D
215D, 219D
2221488
CONTROL & LINES GP-RIDE
980G II, 980H
980G II, 980H