1122077 CONTROL GP-ENG RATINGS ELEK Caterpillar parts
3176
Rating:
Alternative (cross code) number:
CA1122077
112-2077
1122077
CA1122077
112-2077
1122077
Weight: 1 pounds 0 kg.
TRUCK ENGINE,
Related part:
1122077
CONT GP -B
0R6854
R
Compatible equipment models: 1122077:
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01347869
Typical example
Follow Steps 1.a through 1.c to assemble the engine oil cooler.
Ensure that cooler matrix (3) is clean and free from damage. Ensure that housing (5) is clean and free from damage.
Position new joints (4) onto housing (5). Install cooler matrix (3).
Install bolts (6). Tighten the bolts to a torque of 22 N m (16 lb ft).
Clean the mating surface of the cylinder block.
Illustration 2 g06119773
Typical example
Position a new joint (2) on the assembly of engine oil cooler (1). Install fasteners (7) to positions (X) on the assembly of engine oil cooler (1).Note: The holes in the joint have serrations that hold the fasteners captive.
Install the assembly of engine oil cooler (1) to the cylinder block. Tighten bolts (7) finger tight.Note: The fasteners are different lengths. Ensure that the different fasteners are installed in the correct location. Ensure that any brackets that are secured by the fasteners are installed in the correct location.
Illustration 3 g06118967
Tightening sequence for the engine oil cooler
Install remaining fasteners (7) into engine oil cooler (1). Tighten the fasteners to a torque of 22 N m (16 lb ft). Tighten the fasteners in the sequence that is shown in Illustration 3.
If necessary, Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter and Change" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01347869
Typical example
Follow Steps 1.a through 1.c to assemble the engine oil cooler.
Ensure that cooler matrix (3) is clean and free from damage. Ensure that housing (5) is clean and free from damage.
Position new joints (4) onto housing (5). Install cooler matrix (3).
Install bolts (6). Tighten the bolts to a torque of 22 N m (16 lb ft).
Clean the mating surface of the cylinder block.
Illustration 2 g06119773
Typical example
Position a new joint (2) on the assembly of engine oil cooler (1). Install fasteners (7) to positions (X) on the assembly of engine oil cooler (1).Note: The holes in the joint have serrations that hold the fasteners captive.
Install the assembly of engine oil cooler (1) to the cylinder block. Tighten bolts (7) finger tight.Note: The fasteners are different lengths. Ensure that the different fasteners are installed in the correct location. Ensure that any brackets that are secured by the fasteners are installed in the correct location.
Illustration 3 g06118967
Tightening sequence for the engine oil cooler
Install remaining fasteners (7) into engine oil cooler (1). Tighten the fasteners to a torque of 22 N m (16 lb ft). Tighten the fasteners in the sequence that is shown in Illustration 3.
If necessary, Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install".
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter and Change" for the correct procedure.