AVSPARE.COM
parts catalog

CONTROL GP-ENGINE ELECTRONIC 1377392 - Caterpillar


1377392 CONTROL GP-ENGINE ELECTRONIC Caterpillar parts 3406E, C-10, C-12, C-15, C-16, C16
Rating:
28
Alternative (cross code) number:
CA1377392
137-7392
1377392
Caterpillar 1377392 CONTROL GP-ENGINE ELECTRONIC

Buy CONTROL GP-ENGINE ELECTRONIC 1377392 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE, TRUCK ENGINE,

Compatible equipment models: 1377392:

INDUSTRIAL ENGINE  C-10   C-12  
TRUCK ENGINE  3406E   C-10   C-12   C-15   C-16   C16   Caterpillar
Number on catalog scheme: 1
  For full view, you need register

Information:


The oil change interval will be affected by the following items:
Air/fuel ratio
Ambient air conditions
Engine application
Fuel type
Oil type
Size of the oil sumpThe S O S oil analysis program analyzes used oil in order to determine if the oil change interval is suitable for your specific engine. In the absence of S O S oil analysis, change the engine oil and engine oil filters according to the interval that is listed in Table 1.
Table 1
3500B Generator Set Engine Oil Change Intervals    
Engine     Sump Capacity     Oil Change Interval    
Engines With a Standard Sump    
3508B     227 L (60 US gal)     Every 500 Service Hours    
3512B    
318 L (84 US gal)    
3516B    
405 L (107 US gal)    
Engines With a Deep Sump    
3508B    
443 L (117 US gal)     Every 1000 Service Hours    
3512B    
625 L (165 US gal)    
3516B    
807 L (213 US gal)    Drain the Oil
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed when the cold oil is drained. Drain the crankcase when the oil is warm. This method allows proper draining of the waste particles that are suspended in the oil.Failure to follow this recommended procedure will allow the waste particles to be recirculated through the engine lubrication system with the new oil.
After the engine has been operated at normal operating temperature, STOP the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the oil according to the equipment on the engine.
Illustration 1 g00328285
(1) Oil drain
Open oil drain (1) . After the oil has drained, close the oil drain.
If a suction device is inserted into the oil pan, ensure that the suction device is clean. This will prevent dirt from entering into the oil pan. Be careful not to strike the engine oil suction tubes or the piston cooling jets.
If a suction device that attaches to the oil drain is used, ensure that the suction device is clean. Attach the suction device to the oil drain. Open the oil drain. After the oil has drained, close the oil drain and remove the suction device.
If the oil drain valve has a "quick connect" coupling, attach the coupling. Open the drain valve in order to drain the crankcase. After the oil has drained, close the drain valve. Disconnect the coupling.
Replace the engine oil filter elements before you fill the crankcase

Caterpillar parts catalog:

Caterpillar parts catalog
C-10 Truck Engine 3CS00001-UP
C-12 Truck Engine 2KS00001-UP
3406E Truck Engine 2WS00001-UP
3406E Truck Engine 1MM00001-UP
C-15 Truck Engine 6NZ00001-UP
C-16 Truck Engine 7CZ00001-UP
C-10 Industrial Engine BCX00001-UP
C-12 Industrial Engine BDL00001-UP
C-12 Truck Engine CPD00001-UP
C-16 Truck Engine W1A00001-UP


Parts control Caterpillar catalog:

2395025 CONTROL GP-UNPRGMED MONITOR
140G, 3126B, 3412E, 3606, 3608, 3612, 3616, 621B, 627F, 631D, 637D, 657E, 725, 730, 735, 740, 770, 772, 815B, 824C, 844K, 854K, 938H, 950H, 953D, 962H, 963D, 966H, 972H, 973D, 980C, 980G, 980H, 990K, ...
1791747 CONTROL GP-ENGINE ELECTRONIC
3406E, C-10, C-12, C-15, C-16, C16
4174722 CONTROL GP-UNPROGRAMMED
14M, 16M, 24M, 3054C, 3126, 3126B, 3304, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3412, 3412E, 3508C, 3512, 3512B, 3512C, 3516C, C-10, C-12, C-15, C11, C13, C15, C18, C27, C32, C4.4, C7, C9, CX31-C13I, ...
4174723 CONTROL GP-UNPROGRAMMED
3054C, 3126, 3126B, 3304, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3412, 3412E, 3508C, 3512, 3512B, 3512C, 3516C, C-10, C-15, C11, C13, C15, C18, C27, C32, C4.4, C7, C9, CX31-C13I, CX31-C15I, G3306, G34...
2452943 CONTROL GP-UNPRGMED MONITOR
3024, 3116, 3126, 3126B, 3126E, 3176B, 3406E, C-10, C-12, C-15, C-16, C-9, C11, C13, C15, C7, C9, CX28, CX31, CX35, DEUCE, TH31-E61, TH35-C13T, TH35-C15T
1791747 CONTROL GP-ENGINE ELECTRONIC
3406E, C-10, C-12, C-15, C-16, C16
1573705 CONTROL GP-ENGINE ELECTRONIC
3406E, C-10, C-12, C-15, C-16
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.