1519373 CONTROL GP-ENGINE & HYD PUMP Caterpillar parts
322B L
Rating:
Alternative (cross code) number:
CA1519373
151-9373
1519373
CA1519373
151-9373
1519373
Weight: 4 pounds 2 kg.
EXCAVATOR,
Compatible equipment models: 1519373:
Number on catalog scheme:
4
For full view, you need register
Information:
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Forcing Bolt 3/8-16 by 4 inch 2
B 439-3940 Bracket As 1
C 8H-0663 Bearing Puller Gp 1
D 8B-7554 Bearing Cup Puller Gp 1
8B-7548 Push-Puller Tool Gp 1 Start By:
Remove the circle drive.Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This step will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected always.
Illustration 1 g00937730
Remove coupling (1) from housing (3). Remove pin (2) from coupling (1).
Illustration 2 g00937733
Remove nuts (4). Remove bracket (5).
Remove O-ring seal (7) and shims (8).
Remove bearing cup (6) from bracket (5).
Illustration 3 g00937735
Remove bolts (9) and cover (10).
Remove bolts (11).
Illustration 4 g00937707
Install Tooling (A) and remove cover (12).
Illustration 5 g00937728
Remove plug (13) and O-ring seal (14) from cover (12).
Remove bearing (15) from cover (12).
Illustration 6 g00937708
Install Tooling (B) on shaft assembly (16). Attach a suitable lifting device to Tooling (B). The weight of shaft assembly (16) is approximately 32 kg (70 lb).
Remove shaft assembly (16). Remove Tooling (B).
Illustration 7 g00937732
Remove remaining bolts (17) and retainer (18). Remove spacer (19) and shims (20).
Remove spring (21) and spacer (22).
Illustration 8 g00937709
Remove gear (23) from shaft assembly (16). Remove friction discs (24) and discs (25) from gear (23). Remove spacer (26).
Illustration 9 g00937727
Remove thrust washer (27) and remove bearing (28).
Remove worm assembly (29) from housing (3).
Illustration 10 g00937739
Use Tooling (C) and a suitable press to remove bearings (31) from worm assembly (29).
Illustration 11 g00937737
Use Tooling (D) to remove bearing cup (32) from housing (3).
Table 1
Required Tools
Tool Part Number Part Description Qty
A Forcing Bolt 3/8-16 by 4 inch 2
B 439-3940 Bracket As 1
C 8H-0663 Bearing Puller Gp 1
D 8B-7554 Bearing Cup Puller Gp 1
8B-7548 Push-Puller Tool Gp 1 Start By:
Remove the circle drive.Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This step will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected always.
Illustration 1 g00937730
Remove coupling (1) from housing (3). Remove pin (2) from coupling (1).
Illustration 2 g00937733
Remove nuts (4). Remove bracket (5).
Remove O-ring seal (7) and shims (8).
Remove bearing cup (6) from bracket (5).
Illustration 3 g00937735
Remove bolts (9) and cover (10).
Remove bolts (11).
Illustration 4 g00937707
Install Tooling (A) and remove cover (12).
Illustration 5 g00937728
Remove plug (13) and O-ring seal (14) from cover (12).
Remove bearing (15) from cover (12).
Illustration 6 g00937708
Install Tooling (B) on shaft assembly (16). Attach a suitable lifting device to Tooling (B). The weight of shaft assembly (16) is approximately 32 kg (70 lb).
Remove shaft assembly (16). Remove Tooling (B).
Illustration 7 g00937732
Remove remaining bolts (17) and retainer (18). Remove spacer (19) and shims (20).
Remove spring (21) and spacer (22).
Illustration 8 g00937709
Remove gear (23) from shaft assembly (16). Remove friction discs (24) and discs (25) from gear (23). Remove spacer (26).
Illustration 9 g00937727
Remove thrust washer (27) and remove bearing (28).
Remove worm assembly (29) from housing (3).
Illustration 10 g00937739
Use Tooling (C) and a suitable press to remove bearings (31) from worm assembly (29).
Illustration 11 g00937737
Use Tooling (D) to remove bearing cup (32) from housing (3).
Caterpillar parts catalog:
Parts control Caterpillar catalog:
312B L, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 322C, 325B L, 325C, 330B L, 330C L, 330C MH, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 385B, 5090B, 5110B, M325B, W330B, W345B II
322B L, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 5110B, 539, M325B, W330B, W345B II
1337900
CONTROL GP-HANDLE
311B, 312B, 315B, 318B, 320B, 320B L, 320B U, 321B, 322B, 322B L, 325B, 325B L, 330B, 330B L, 345B, 345B II, 345B L, 365B, 365B L, 385B, 5110B
311B, 312B, 315B, 318B, 320B, 320B L, 320B U, 321B, 322B, 322B L, 325B, 325B L, 330B, 330B L, 345B, 345B II, 345B L, 365B, 365B L, 385B, 5110B
1051695
CONTROL GP-FUEL INJECTION
120H, 120H ES, 120H NA, 135H, 135H NA, 3116, 3126, 320 L, 320B, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325B, 325B L, 35, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M,...
120H, 120H ES, 120H NA, 135H, 135H NA, 3116, 3126, 320 L, 320B, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325B, 325B L, 35, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M,...
311B, 312B, 312B L, 315B, 315B FM L, 315B L, 317B LN, 318B, 320B, 320B FM LL, 320B L, 320B U, 322B, 322B L, 322B LN, 325B, 325B L, 330B, 330B L, 345B, 345B II, 345B II MH, 345B L, W330B, W345B II
1337899
CONTROL GP-HANDLE
311B, 312B, 315B, 318B, 320B, 320B L, 320B U, 321B, 322B, 322B L, 325B, 325B L, 330B, 330B L, 345B, 345B II, 345B L, 365B, 365B L, 385B, 5110B
311B, 312B, 315B, 318B, 320B, 320B L, 320B U, 321B, 322B, 322B L, 325B, 325B L, 330B, 330B L, 345B, 345B II, 345B L, 365B, 365B L, 385B, 5110B
1327806
CONTROL GP-GOVERNOR
322B, 322B L, 322B LN, 325B, 325B L, M325B
322B, 322B L, 322B LN, 325B, 325B L, M325B
1384665
CONTROL AR-AUXILIARY
322B L
322B L
1060106
CONTROL GP-GOVERNOR
322B L, 325B L
322B L, 325B L
1190611
CONTROL & MTG GP-MACHINE
322B, 322B L, 322B LN
322B, 322B L, 322B LN
1453133
CONTROL GP-MACHINE
322B, 322B L
322B, 322B L
1384464
CONTROL AR-AUXILIARY
322B L, 322B LN
322B L, 322B LN
1564278
CONTROL GP-MONITOR
515, 525
515, 525
1750027
CONTROL GP-MONITOR
515, 525, 545
515, 525, 545
1695426
CONTROL GP-XMSN ELECTRONIC
515, 525
515, 525
1357122
CONTROL GP-XMSN ELECTRONIC
515, 525
515, 525
1367624
CONTROL GP-XMSN ELECTRONIC
515, 525
515, 525
1749105
CONTROL GP-HANDLE
320B, 322B LN, 325B L, 330B L, 345B L, 365B
320B, 322B LN, 325B L, 330B L, 345B L, 365B
1229897
CONTROL GP-IMPLEMENT
320B, 320B L, 322B L, 322B LN, 325B L, 330B L, 345B II, 345B L
320B, 320B L, 322B L, 322B LN, 325B L, 330B L, 345B II, 345B L