1879974 CONTROL GP-JOYSTICK Caterpillar parts
307C, 308C, 312C L, 314C, 315C, 318C, 320C, 320C FM, 321C, 322C, 322C FM, 325C, 325C FM, 330C FM, 330C L, 330C MH
Rating:
Alternative (cross code) number:
CA1879974
187-9974
1879974
CA1879974
187-9974
1879974
Weight: 5 pounds 2 kg.
EXCAVATOR, MINI HYD EXCAVATOR,
Compatible equipment models: 1879974:
Information:
Governor (Dashpot Governor)
1. Remove cover (1), plate assembly (2), and adapter group (3) from the governor. 2. Remove the bolt that holds collar (4) on the bolt. Remove cover (5) and the spring under the collar. 3. Remove bolts (6) and governor housing (7). Remove the gasket that is under the governor housing. 4. Disconnect two fuel lines (8) from the plate group. Remove seat (9) and spring (10). 5. Remove bolts (12) that hold the plate group (13) on the fuel injection pump housing. Remove the plug from the side of the fuel injection pump housing and install tooling (A).6. Pull the bolt (11) up to put the rack in the center position. The rack is in the center position when it is against tool (A).7. Remove adapter group (13). Keep bolt (11) pulled up to keep the rack in the center position. If the rack is not in the center position, the lever on the bottom of the plate group will prevent the plate group from being removed from the fuel injection pump housing.Install Governor (Dashpot Governor)
Do not install the plate group until drive assembly (3) is removed from the plate group.
1. Remove ring (1), dowel (2), and drive assembly (3) from the plate group. 2. Install tool (A) in the side of the fuel injection pump housing. Move the rack against tool (A). This puts the rack in the center position. The fuel rack must be in the center position so lever (5) can be put in alignment with the groove (slot) in the rack. A small amount of force on the end of tool (A) will be needed to keep the rack in the center position.3. Install plate group (4) on the fuel injection pump housing. Make sure lever (5) aligns with the groove (slot) in the rack. Remove tool (A). 4. Install drive assembly (7) in the drive group. Make sure that the groove in the bottom of the drive assembly is in alignment with the pin in the pinion in the fuel injection pump housing. Make sure hole (6) and hole (9) in gear (8) are in alignment. 5. Install pin (11) that holds drive assembly (7) in position in gear (8).6. Install ring (10) to hold pin (11) in position in the gear. 7. Connect two fuel lines (12) to the plate group.8. Install spring (14) and seat (13). 9. Install gasket (16) and governor housing (15). Install the bolts that hold it in place. 10. Install spring (18) and collar (17) on bolt (19). Install the bolt that holds the collar on bolt (19). 11. Install gasket (22) and adapter group (20) on the governor housing. Make sure lever (21) is in position under collar (17). 12. Put the gasket and plate assembly (24) in position on adapter group (20). Make sure the pin on plate assembly (24) is in the groove (slot) in the collar.13. Install the gaskets and two covers (23) on the plate assembly.14. Check the governor
1. Remove cover (1), plate assembly (2), and adapter group (3) from the governor. 2. Remove the bolt that holds collar (4) on the bolt. Remove cover (5) and the spring under the collar. 3. Remove bolts (6) and governor housing (7). Remove the gasket that is under the governor housing. 4. Disconnect two fuel lines (8) from the plate group. Remove seat (9) and spring (10). 5. Remove bolts (12) that hold the plate group (13) on the fuel injection pump housing. Remove the plug from the side of the fuel injection pump housing and install tooling (A).6. Pull the bolt (11) up to put the rack in the center position. The rack is in the center position when it is against tool (A).7. Remove adapter group (13). Keep bolt (11) pulled up to keep the rack in the center position. If the rack is not in the center position, the lever on the bottom of the plate group will prevent the plate group from being removed from the fuel injection pump housing.Install Governor (Dashpot Governor)
Do not install the plate group until drive assembly (3) is removed from the plate group.
1. Remove ring (1), dowel (2), and drive assembly (3) from the plate group. 2. Install tool (A) in the side of the fuel injection pump housing. Move the rack against tool (A). This puts the rack in the center position. The fuel rack must be in the center position so lever (5) can be put in alignment with the groove (slot) in the rack. A small amount of force on the end of tool (A) will be needed to keep the rack in the center position.3. Install plate group (4) on the fuel injection pump housing. Make sure lever (5) aligns with the groove (slot) in the rack. Remove tool (A). 4. Install drive assembly (7) in the drive group. Make sure that the groove in the bottom of the drive assembly is in alignment with the pin in the pinion in the fuel injection pump housing. Make sure hole (6) and hole (9) in gear (8) are in alignment. 5. Install pin (11) that holds drive assembly (7) in position in gear (8).6. Install ring (10) to hold pin (11) in position in the gear. 7. Connect two fuel lines (12) to the plate group.8. Install spring (14) and seat (13). 9. Install gasket (16) and governor housing (15). Install the bolts that hold it in place. 10. Install spring (18) and collar (17) on bolt (19). Install the bolt that holds the collar on bolt (19). 11. Install gasket (22) and adapter group (20) on the governor housing. Make sure lever (21) is in position under collar (17). 12. Put the gasket and plate assembly (24) in position on adapter group (20). Make sure the pin on plate assembly (24) is in the groove (slot) in the collar.13. Install the gaskets and two covers (23) on the plate assembly.14. Check the governor
Caterpillar SIS machinery equipment:
Caterpillar SIS
320C & 320C L Excavators AMC00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
322C & 322C L Excavators BKM00001-UP (MACHINE) POWERED BY 3126 Engine »
187-9974
CONTROL GP-JOYSTICK
307C & 307C SB Excavators BCM00001-UP (MACHINE) POWERED BY 4M40 Engine »
187-9974
CONTROL GP-JOYSTICK
312C & 312C L Excavators CBA00001-01200 (MACHINE) »
187-9974
CONTROL GP-JOYSTICK
322C L Excavator BKJ00001-UP (MACHINE) POWERED BY 3126 Engine »
187-9974
CONTROL GP-JOYSTICK
320C Forest Swing Machine BGB00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
325C & 325C L Excavators BKW00001-UP (MACHINE) POWERED BY 3126B Engine »
187-9974
CONTROL GP-JOYSTICK
325C FOREST SWING MACHINES G1L00001-UP (MACHINE) POWERED BY 3126B Engine »
187-9974
CONTROL GP-JOYSTICK
315C & 315C L Excavators CFB00001-UP (MACHINE) POWERED BY 3046 Engine »
187-9974
CONTROL GP-JOYSTICK
320C U 320C LU Excavators CLM00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
322C FOREST SWING MACHINES BPH00001-UP (MACHINE) POWERED BY 3126 Engine »
187-9974
CONTROL GP-JOYSTICK
325C L Excavator BFE00001-UP (MACHINE) POWERED BY 3126B Engine »
187-9974
CONTROL GP-JOYSTICK
330C & 330C L Excavators JAB00001-UP (MACHINE) POWERED BY C-9 Engine »
187-9974
CONTROL GP-JOYSTICK
330C L Excavator DKY00001-UP (MACHINE) POWERED BY C-9 Engine »
187-9974
CONTROL GP-JOYSTICK
308C CR Excavator KCX00001-UP (MACHINE) POWERED BY 4M40 Engine »
187-9974
CONTROL GP-JOYSTICK
314C CR & 314C LCR Excavators KJA00001-UP (MACHINE) POWERED BY 3064 Engine »
187-9974
CONTROL GP-JOYSTICK
318C L & 318C LN Excavators GPA00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
330C Hydraulic Material Handler D3C00001-UP (MACHINE) POWERED BY C-9 Engine »
187-9974
CONTROL GP-JOYSTICK
330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine »
187-9974
CONTROL GP-JOYSTICK
320C & 320C L Excavators MAB00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
322C & 322C L Excavators DAA00001-UP (MACHINE) POWERED BY 3126 Engine »
187-9974
CONTROL GP-JOYSTICK
320C U & 320C LU Excavators MAC00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine »
187-9974
CONTROL GP-JOYSTICK
322C L Hydraulic Excavator HEK00001-UP (MACHINE) POWERED BY 3126B Engine »
187-9974
CONTROL GP-JOYSTICK
315C & 315C L Excavators AKE00001-UP (MACHINE) POWERED BY 3046 Engine »
187-9974
CONTROL GP-JOYSTICK
321C LCR Hydraulic Excavator MCF00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
320C Forest Machines SAH00001-UP (MACHINE) POWERED BY 3066 Engine »
187-9974
CONTROL GP-JOYSTICK
312C & 312C L Excavators CBA01201-UP (MACHINE) POWERED BY 3064 Engine »
187-9974
CONTROL GP-JOYSTICK
322C Forest Swing Machines C3R00001-UP (MACHINE) POWERED BY 3126B Engine »
187-9974
CONTROL GP-JOYSTICK
Caterpillar parts catalog:
Parts control Caterpillar catalog:
1385190
CONTROL GP-ENGINE ELECTRONIC
307, 307B, 307C, 308C, 313B, 315B, 315B FM L, 315C, 317B LN, 318B
307, 307B, 307C, 308C, 313B, 315B, 315B FM L, 315C, 317B LN, 318B
1573165
CONTROL GP-UNPROGRAMMED
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 321C, 322C, 325C, 330C, 330C FM, 330C L, 330C MH, M325C MH
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 321C, 322C, 325C, 330C, 330C FM, 330C L, 330C MH, M325C MH
2238831
CONTROL
320C FM, 330C FM
320C FM, 330C FM
2115537
CONTROL AS-ELECTRONIC
320C, 325C
320C, 325C
2555641
CONTROL GP-HANDLE
322C FM, 325C FM, 345C, 345C MH, W345C MH
322C FM, 325C FM, 345C, 345C MH, W345C MH
2475243
CONTROL GP
320C
320C
2115538
CONTROL AS
320C FM
320C FM
2307662
CONTROL GP
320C FM, 325B L, 325C, 325C L, 325D MH, 330B L, 330C L, 330C MH, 330D MH, 345B, 345B II, 345B II MH, 345C, 345C MH, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M325B, M325C MH, M325D L MH, M325D MH, M...
320C FM, 325B L, 325C, 325C L, 325D MH, 330B L, 330C L, 330C MH, 330D MH, 345B, 345B II, 345B II MH, 345C, 345C MH, 365B, 365B II, 365C L MH, 375 L, 385C L MH, M325B, M325C MH, M325D L MH, M325D MH, M...
2371036
CONTROL
330C FM
330C FM
1W5888
CONTROL GP-FUEL RATIO
3408, 3408C
3408, 3408C
3N8029
CONTROL GP-GOVERNOR
3408, 3408C, 3412, 3412C, 3412D
3408, 3408C, 3412, 3412C, 3412D
5N1613
CONTROL GP-VOLTAGE-MANUAL
3208, 3304, 3306, 3406, 3406B, 3408, 3412, 3412C, G3306, G3408, G3412, SR4
3208, 3304, 3306, 3406, 3406B, 3408, 3412, 3412C, G3306, G3408, G3412, SR4
1060113
CONTROL & MTG GP-MACHINE
325B, 325B L, M325B
325B, 325B L, M325B
2713097
CONTROL GP-HANDLE
420E, 420F, 430E, 430F, 432E, 432F, 434E, 442E, 444E, 444F, 450E, 450F
420E, 420F, 430E, 430F, 432E, 432F, 434E, 442E, 444E, 444F, 450E, 450F
2921970
CONTROL GP-CLEAN GAS INDUCTION
C13, TH35-C13T
C13, TH35-C13T
2W3157
CONTROL GP-FUEL RATIO
3408, 3408B, 3408C, 3412, 3412C, 589, 631D, 631E, 633D, 637D, 637E, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 834B, 836, 988B, 990, 992C, 992D, D10N, D8L, D9L, D9N, D9R
3408, 3408B, 3408C, 3412, 3412C, 589, 631D, 631E, 633D, 637D, 637E, 651E, 657E, 768C, 769C, 771C, 772B, 773B, 775B, 834B, 836, 988B, 990, 992C, 992D, D10N, D8L, D9L, D9N, D9R
2885951
CONTROL GP-AIR
C13, TH35-C13T
C13, TH35-C13T
2885950
CONTROL GP-AIR
C13, TH35-C13T
C13, TH35-C13T
6I5351
CONTROL GP-PILOT OPERATED HYD
312, 315, 317, 320 L, 322 LN, 325 L, 330 L, 350, 375, 375 L, 5130, 5230
312, 315, 317, 320 L, 322 LN, 325 L, 330 L, 350, 375, 375 L, 5130, 5230