2015954 CONTROL GP-DIRECTION & SPEED Caterpillar parts
CP-433E, CS-423E, CS-433E
Rating:
Alternative (cross code) number:
CA2015954
201-5954
2015954
CA2015954
201-5954
2015954
VIBRATORY COMPACTOR,
Information:
Illustration 1 g01520601Note: Before assembly, apply 5P-3975 Rubber Lubricant to six liner seals.Bore in the cylinder block for the cylinder liners Position (A) ... 151.50 0.03 mm (5.965 0.001 inch)Position (B) ... 149.8 0.3 mm (5.90 0.01 inch)Position (C) ... 148.00 0.03 mm (5.827 0.001 inch)Position (D) ... 141.90 0.05 mm (5.587 0.002 inch)
Illustration 2 g01663656
Front view of engine
Note: Before assembly, apply 4C-9506 Retaining Compound to the cup plugs (1). (1) Installation depth of three cup plugs ... 1.25 0.25 mm (0.049 0.010 inch) (E) Diameter of the camshaft bores ... 85.000 0.025 mm (3.3464 0.0010 inch) (G) Distance from the centerline of the crankshaft bore to the top surface of the cylinder block ... 387 mm (15.2 inch) (H) Bore in the cylinder block for seven main bearings ... 116.000 0.013 mm (4.5669 0.0005 inch) (J) Distance from the centerline of the crankshaft bore to the bottom surface of the cylinder block ... 120 mm (4.7 inch) (K) Dimension for the crankshaft main bearing cap Width of the crankshaft main bearing cap ... 178.00 0.02 mm (7.008 0.001 inch)Width of the cylinder block for the crankshaft main bearing cap ... 178.000 0.018 mm (7.0079 0.0007 inch) (2) Use the following procedure to tighten the crankshaft main bearing cap bolts:
Orient the bearing cap correctly. The part number on the bearing cap must face to the right and to the front face of the block. Also, the tab slots that are in the block and the bearing caps must be adjacent.
The bearing caps are marked with identification numbers 1 through 7. Install the bearing caps into the correct positions.
Lubricate the threads and the washer face of the crankshaft main bearing cap bolts with clean engine oil, molylube or an approved equivalent.
Tighten the bolts to 150 5 N m (110 4 lb ft).
Again, tighten the bolts to an additional angle of 60 5 degrees.
Illustration 3 g01663655
Section F-F
Camshaft bearings must be installed into their correct position. Failure to do so will result in engine damage.
Install seven bearings for the camshaft to the following depth in the cylinder block. The distance that is listed below is measured from the front face of the cylinder block. Position (L) ... 972.5 mm (38.29 inch)Position (M) ... 816.5 mm (32.15 inch)Position (N) ... 660.5 mm (26.00 inch)Position (P) ... 504.5 mm (19.86 inch)Position (Q) ... 348.5 mm (13.72 inch)Position (R) ... 192.5 mm (7.58 inch)Position (S) ... 36.5 mm (1.44 inch)
Illustration 4 g01663654
Section T-T
(3) Bearing joint
(4) Oil hole (U) Bearing oil hole is located at a 45 degrees angle from vertical. All seven bearings for the camshaft have the same angle.
Illustration 5 g01525437
Right side view of engine
Note: Before assembly, apply 4C-9506 Retaining Compound to the cup plugs (5). (5) Installation depth of three cup plugs ... 1.25 0.50 mm (0.049 0.020 inch) (6) Before assembly, apply 4C-4030 Thread Lock Compound to the threads
Caterpillar SIS machinery equipment:
Caterpillar SIS
CS-423E Vibratory Compactor CFX00001-UP (MACHINE) POWERED BY 3054B Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor CFX00001-UP (MACHINE) POWERED BY 3054B Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-433E,CP-433E Vibratory Compactor CFK00001-UP (MACHINE) POWERED BY 3054 Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-433E,CP-433E Vibratory Compactor CFK00001-UP (MACHINE) POWERED BY 3054 Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor ASH00001-UP (MACHINE) »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-433E,CP-433E Vibratory Compactor CYE00001-UP (MACHINE) POWERED BY 3054 Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-433E,CP-433E Vibratory Compactor CYE00001-UP (MACHINE) POWERED BY 3054 Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor DCL00001-UP (MACHINE) POWERED BY 3054B Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor DCL00001-UP (MACHINE) POWERED BY 3054B Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor BWG00001-UP (MACHINE) POWERED BY 3054C Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor EAE00001-UP (MACHINE) POWERED BY 3054C Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-423E Vibratory Compactor AST00001-UP (MACHINE) POWERED BY 3054C Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS/CP-433E Vibratory Compactor BTT00001-UP (MACHINE) POWERED BY 3054C Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS/CP-433E Vibratory Compactor ASN00001-UP (MACHINE) POWERED BY 3054C Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
CS-433 E Vibratory Soil Compactor MC200001-UP (MACHINE) POWERED BY 3054C Engine »
201-5954
CONTROL GP-DIRECTION & SPEED
Caterpillar parts catalog:
Parts control Caterpillar catalog:
3262350
CONTROL GP-DIRECTION & SPEED
CP-44, CS-44
CP-44, CS-44
9V6740
CONTROL GP-MECHANICAL HYD
IT18, IT18B, IT28, IT28B
IT18, IT18B, IT28, IT28B
3061528
CONTROL AR-COUPLER
345D, 345D L, 349D, 349D L
345D, 345D L, 349D, 349D L
1884908
CONTROL GP-PILOT OPERATED HYD
TH63, TH82, TH83
TH63, TH82, TH83
2093376
CONTROL GP-GOVERNOR
420E, 430E, 450E
420E, 430E, 450E
2390572
CONTROL & MTG GP-MONITOR
784C, 785C, 789C, 789D, 793C
784C, 785C, 789C, 789D, 793C
2541164
CONTROL GP-SERVICE BRAKE
797, 797B
797, 797B
4W2967
CONTROL GP-FUEL INJECTION
3126, 3516, 789, 793, 994, PM3516
3126, 3516, 789, 793, 994, PM3516
1062359
CONTROL GP-STEERING
814F, 815F, 816F, 938F, 950F, 950F II, 960F, 966F, 966F II, 970F, IT38F
814F, 815F, 816F, 938F, 950F, 950F II, 960F, 966F, 966F II, 970F, IT38F
3782495
CONTROL GP-PILOT OPERATED HYD
303.5E, 304E, 305.5E, 305E
303.5E, 304E, 305.5E, 305E
1906728
CONTROL GP-BUCKET
950G II, 950H, 962G II, 962H
950G II, 950H, 962G II, 962H