CONTROL GP-HANDLE 2041395 - Caterpillar

2041395 CONTROL GP-HANDLE Caterpillar parts 216, 236, 247, 267, 287

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2041395
204-1395
2041395

Weight: 0.44 pounds 0 kg.

Buy CONTROL GP-HANDLE 2041395 Caterpillar genuine, new aftermarket tractor parts with delivery
MULTI TERRAIN LOADER, SKID STEER LOADER,

You can buy:

US$525.00

15 Jul 2025

FridayParts

Left Side Joystick Handle Controller 204-1395 for Caterpillar CAT Loader 226 232 236 246 247 248 252 257 267 277 287

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Lenox RX+ 20 1/2X1 1/2 .050 4/6 VPVREHS (2041395)

$202.82

12 Feb 2020

-: -

Lenox RX+ 20 1/2X1 1/2 .050 4/6 VPVREHS (2041395)

S Husky Toucan Bird Doormat Cute Animal Pattern Welcome Doormat Non-Slip Carpet Outdoor Front Rug for Entry 31 x 20 in 2041395

$20.99

03 Nov 2021

CN: S Husky(Holiday

S Husky Toucan Bird Doormat Cute Animal Pattern Welcome Doormat Non-Slip Carpet Outdoor Front Rug for Entry 31 x 20 in 2041395
S Husky Size: 31 x 20 inches (79 x 51 cm). || Senior Material: Polyester, sponge, non-woven fabric which are absorbent, soft, wear-resistant and delicate high density memory foam. || Multi-function: warm house / holiday party gift, holiday decoration, entrance channel, door, office, garden, outdoor, bath mat. || Ideal Gifts: Not only decoring your home when holiday or themed party,also as a perfect festival/housewarming presents. || Gentle hand wash separately in cold water.

This part in 6 request: Show. This information for suppliers only!

2024-07-11

2023-04-07

2022-04-20

2022-03-06

2019-02-28

2018-03-06

Number on catalog scheme: 6

Caterpillar 2041395 Parts scheme CONTROL GP-HANDLE

For full view, you need register

Compatible equipment models: 2041395:

MULTI TERRAIN LOADER 247 267 287

SKID STEER LOADER 216 236 Caterpillar

Information:

Illustration 1 g01215328
Schematic for the 5 volt pressure sensor supplyTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Illustration 2 g01215338
Right side engine view and left side engine view (1) J2/P2 ECM conntector (2) Fuel pressure sensor (3) Engine oil pressure sensor (4) Atmospheric pressure sensor (5) Intake manifold pressure sensor
Thoroughly inspect ECM connectors (1). Also, thoroughly inspect the connectors for each pressure sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01204484
P2 terminal locations (P2-15) Intake manifold pressure sensor (P2-17) Sensor return (P2-28) Engine oil pressure (P2-40) Fuel pressure (P2-57) Atmospheric pressure (P2-72) +5 V supply
Illustration 4 g01215393
Sensor connector (Terminal A) +5 V supply (Terminal B) Sensor return (Terminal C) Sensor signal
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw of each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points from the pressure sensors back to the ECM.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The harness and connectors appear to be OK. There may be a problem in the harness between the ECM and the sensor connector. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Restore electrical power to the ECM.
Monitor the active diagnostic code screen on Cat ET. Check for an active 262-03 code and an active 262-04 code.Note: Wait at least 30 seconds in