2095500 CONTROL GP-ENGINE ELECTRONIC Caterpillar parts
G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
Rating:
Alternative (cross code) number:
CA2095500
209-5500
2095500
CA2095500
209-5500
2095500
Weight: 4 pounds 2 kg.
GAS ENGINE, POWER MODULE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$825.32
08 Aug 2021
5.0[2.25] Pounds
US: AsaPerformance
Nitrous Express 20955-00 Nitrous Plate System Incl. Fuel Line Adapter/Braided Line/WOT activation Switch/Relay/Relay Harness/Master Arming Switch/35-250 WHP Jetting/Hardware Nitrous Plate System
Nitrous Express 1986-1993 Mustang GT || Single Throttle Body Spray Plate || 35, 50, 75, 100, 125, 150, 200, 250 WHP || Bottle Not Included
Nitrous Express 1986-1993 Mustang GT || Single Throttle Body Spray Plate || 35, 50, 75, 100, 125, 150, 200, 250 WHP || Bottle Not Included
Compatible equipment models: 2095500:
Information:
Illustration 1 g01449856
Circuit of the Implement Power Management SolenoidThis diagnostic code is associated with the Hydraulic Pump Torque Limit Solenoid (Implement Power Management Solenoid). The FMI 06 means that the ECM has determined that there is a short to ground in the solenoid circuit.The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2970 FMI 06 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The FMI 06 changes to FMI 05 when the solenoid is disconnected.Results:
YES - The FMI 06 changes to FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J1-52 (wire P988-OR) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-52 (wire P988-OR) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors in order to make sure that the connectors are fully seated. Also, make sure that the clips for each
Caterpillar parts catalog:
Parts control Caterpillar catalog:
1180175
CONTROL GP-EMCP ELECTRONIC
3126B, 3208, 3304, 3304B, 3306, 3306B, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3516, 3516B, 3516C, C-12, C15, C18, C27, C32, C9, G3304, G3306, G3306B, G3406, G34...
3126B, 3208, 3304, 3304B, 3306, 3306B, 3406B, 3406C, 3406E, 3408, 3408C, 3412, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3516, 3516B, 3516C, C-12, C15, C18, C27, C32, C9, G3304, G3306, G3306B, G3406, G34...
2364558
CONTROL GP-EMCP ELECTRONIC
3208, 3304B, 3306B, 3406C, 3408, 3408C, 3412, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3516, 3516B, C18, G3306, G3306B, G3408C, G3412, G3508, G3512, G3512E, G3516, G3516B, G3516C, G3516E, G3520C, G3520E...
3208, 3304B, 3306B, 3406C, 3408, 3408C, 3412, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3516, 3516B, C18, G3306, G3306B, G3408C, G3412, G3508, G3512, G3512E, G3516, G3516B, G3516C, G3516E, G3520C, G3520E...
1315453
CONTROL AS-ELECTRONIC GOVERNOR
3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C, C15, C18, G3304, G3306, G3306B, G3406, G3408, G3408B, G3412, G3508, G...
3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, 3508, 3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C, C15, C18, G3304, G3306, G3306B, G3406, G3408, G3408B, G3412, G3508, G...
1546713
CONTROL GP-ENGINE ELECTRONIC
G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
2567512
CONTROL GP-COMMUNICATION
3176B, 3176C, 3196, 3406E, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, C175-16, C18, C280-12, C280-16, CG137-12, G3406, G3408, G3408C, G3412, G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G...
3176B, 3176C, 3196, 3406E, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, C175-16, C18, C280-12, C280-16, CG137-12, G3406, G3408, G3408C, G3412, G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G...
1935762
CONTROL GP-IGNITION
G3516B, PMG3516
G3516B, PMG3516
3216994
CONTROL GP-MONITOR
G3520B
G3520B
3687108
CONTROL GP-UNPROGRAMMED
CG137-08, CG137-12, G3408, G3408C, G3412, G3508, G3512, G3516
CG137-08, CG137-12, G3408, G3408C, G3412, G3508, G3512, G3516
1252077
CONTROL AS-GOVERNOR
G3508, G3512, G3516
G3508, G3512, G3516
1509410
CONTROL GP-ENG RATINGS ELEK
3412, 3412C
3412, 3412C
1509413
CONTROL GP-ENG RATINGS ELEK
3412, 3412C
3412, 3412C
1403009
CONTROL AS-VOLTAGE
3306B, 3406C
3306B, 3406C
1761286
CONTROL GP-ENGINE MONITORING
G3512E, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
G3512E, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
3482392
CONTROL GP-ENGINE ELECTRONIC
G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
G3508, G3508B, G3512, G3512B, G3512E, G3516, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
3223617
CONTROL GP-ENGINE ELECTRONIC
G3508, G3508B, G3512, G3512E, G3516, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516
G3508, G3508B, G3512, G3512E, G3516, G3516B, G3516C, G3516E, G3520B, G3520C, G3520E, PMG3516