2122282 CONTROL GP-MONITOR Caterpillar parts
PM-201, PM-565B
Rating:
Alternative (cross code) number:
CA2122282
212-2282
2122282
CA2122282
212-2282
2122282
Weight: 6 pounds 2 kg.
COLD PLANER,
This part in 2 request:
Show.
This information for suppliers only!
2016-08-31
2016-08-31
Information:
Table 1
Required Tools
Part Number Description Qty
9U-7400 Multitach Tool Group 1
Position the machine on level ground.
Stop the engine.
Install 9U-7400 Multitach Tool Group on the engine.
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Read the engine speed display (rpm) on the multitach. Refer to Table 2 for the specifications for engine speed at the desired engine operation.
Table 2
ODPS Disabled
Item Specifications
New Rebuild Service Limit
No Load High Idle(1) 2165 50 rpm(2) 1965 to 2215 rpm(2)
2265 50 rpm(3) 2065 to 2215 rpm(3)
No Load Low Idle 900 50 rpm 900 100 rpm
Maximum speed with load(4) 2000 rpm(5) 1900 rpm(5)
No load speed(6) 1300 50 rpm 1300 100
High Idle Rise Up With Travel(7) 2365 50 rpm 2365 +50 - 200 rpm
(1) AEC switch in the OFF position
(2) Three seconds after the engine speed dial was placed at position "10"
(3) Engine rpm within three seconds after the engine speed dial was placed at position "10"
(4) Pressure is relieved from both pumps (stall condition).
(5) Minimum rpm
(6) AEC switch in the ON position
(7) If Equipped
Table 3
ODPS Enabled
Item Specifications
New Rebuild Service Limit
No Load High Idle(1) 2025 50 rpm(2) 1925 to 2175 rpm(2)
2125 50 rpm(3) 2075 to 2175 rpm(3)
No Load Low Idle 900 50 rpm 900 100 rpm
Maximum speed with load(4) 2000 rpm(5) 1900 rpm(5)
No load speed(6) 1300 50 rpm 1300 100 rpm
(1) AEC switch in the OFF position
(2) Three seconds after the engine speed dial was placed at position "10"
(3) Engine rpm within three seconds after the engine speed dial was placed at position "10"
(4) Pressure is relieved from both pumps (stall condition).
(5) Minimum rpm
(6) AEC switch in the ON positionNote: A New specification is the performance that can be expected for a new machine. A Rebuild specification is the performance that can be expected after rebuilding the components of a system. Performance beyond the Service Limit is an indication of these problems: improper maintenance or adjustment, component wear and failure.
Caterpillar parts catalog:
Parts control Caterpillar catalog:
1G9504
CONTROL GP-BACKUP
PM-201, PM-565, PM-565B
PM-201, PM-565, PM-565B
2417598
CONTROL & MTG GP-ENGINE ELEK
651B, 657E, 657G, 770, 772, PM-200, PM-201
651B, 657E, 657G, 770, 772, PM-200, PM-201
2851133
CONTROL GP-UNPROGRAMMED
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 140K, 140K 2, 140M, 140M 2, 14M, 160K, 160M, 160M 2, 16M, 2384C, 2470C, 2484C, 24M, 2570C, 2670C, 2864C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2...
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 140K, 140K 2, 140M, 140M 2, 14M, 160K, 160M, 160M 2, 16M, 2384C, 2470C, 2484C, 24M, 2570C, 2670C, 2864C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2...
2622879
CONTROL GP-UNPROGRAMMED
324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D...
324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D...
3722906
CONTROL GP-UNPROGRAMMED
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 651B, 657E, 657G, 770, 772, 950H, 962H, AP-755, C7, C9, IT62H, PM-200, PM-201, W345C MH
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 651B, 657E, 657G, 770, 772, 950H, 962H, AP-755, C7, C9, IT62H, PM-200, PM-201, W345C MH
1G9998
CONTROL-FLOW
PM-465, PM-565, PM-565B, PR-1000, PR-450C
PM-465, PM-565, PM-565B, PR-1000, PR-450C
1467546
CONTROL GP-MONITOR
PM-565, PM-565B
PM-565, PM-565B
2598740
CONTROL GP-ACCELERATION
CB-334E
CB-334E
2828241
CONTROL GP-UNPROGRAMMED
AP-1055D, AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D
AP-1055D, AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG-2455D, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D
2497139
CONTROL GP-ELECTRONIC
RM-300, RM-500
RM-300, RM-500
2308215
CONTROL GP-ADDITIVE
RM-300, RM-500
RM-300, RM-500
2549774
CONTROL GP-ACCELERATION
CB-334E
CB-334E
3688125
CONTROL GP-ELECTRONIC
CP-56, CP-64, CP-76, CS-64, CS-74
CP-56, CP-64, CP-76, CS-64, CS-74
3136383
CONTROL GP-DIRECTION & SPEED
CP-56, CP-64, CP-76, CS-54, CS-56, CS-64, CS-74
CP-56, CP-64, CP-76, CS-54, CS-56, CS-64, CS-74
2838323
CONTROL AS-STEERING
AP-655D, AP1055E, AP555E, BG1055E, BG655D
AP-655D, AP1055E, AP555E, BG1055E, BG655D
3395421
CONTROL GP-MACHINE
CB-564D
CB-564D
2838698
CONTROL GP-UNPROGRAMMED
CB-534D, CB-564D
CB-534D, CB-564D